Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0356879 ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM(w/o Brake pedal Load Sensing Switch)  Brake Warning Light does not Come ON  


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK BRAKE WARNING LIGHT
a.

Disconnect the skid control ECU connector.


b.

Turn the ignition switch to ON.


c.

Check that the brake warning light comes on.

OK:

The brake warning light comes on.


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER AND PARKING BRAKE SWITCH)
2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER AND PARKING BRAKE SWITCH)
a.

Turn the ignition switch off.


b.

Disconnect the combination meter connector.


c.

Disconnect the parking brake switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-19 (PKB) - L2-1 (+)*1
A50-19 (PKB) - G2-1 (+)*2
Always Below 1 Ω
A50-19 (PKB) or L2-1 (+) - Body ground*1
A50-19 (PKB) or G2-1 (+) - Body ground*2
Always 10 kΩ or higher
J1-11 (PKBI) - L2-1 (+)*1
J1-11 (PKBI) - G2-1 (+)*2
Always Below 1 Ω
J1-11 (PKBI) or L2-1 (+) -Body ground*1
J1-11 (PKBI) or G2-1 (+) -Body ground*2
Always 10 kΩ or higher
A50-19 (PKB) - J1-11 (PKBI) Always Below 1 Ω
A50-19 (PKB) or J1-11 (PKBI) - Body ground Always 10 kΩ or higher
L2-2 (E) - Body ground*1
G2-2 (E) - Body ground*2
Always Below 1 Ω


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

3.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the skid control ECU connector.


b.

Reconnect the parking brake switch connector.


c.

Reconnect the combination meter connector.


d.

Check the combination meter (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

OK:

The combination meter is normal.


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM (w/o Brake pedal Load Sensing Switch)>PROBLEM SYMPTOMS TABLE).



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU

NG

REPLACE COMBINATION METER ASSEMBLY