Home › Engine / Hybrid System › 2TR-FE COOLING › COOLANT
RM2850E _51 Engine / Hybrid System _073291 2TR-FE COOLING _0356993 COOLANT A

2TR-FE COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 51405A 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 58734B 3.REMOVE REAR ENGINE SERVICE COVER WEATHERSTRIP

Hide 58420 5.REMOVE NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 6.DRAIN ENGINE COOLANT

CAUTION:

To avoid the danger of being burned, do not remove the water filler cap while the engine and radiator are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator.


a.

Loosen the radiator drain plug.

A156733E03
4.521,2.813 4.729,2.813 false 4.646,2.302 4.844,2.302 false 3.656,1.208 3.938,0.396 3.938,0.396 4.052,0.396 false 2.625,2.25 2.094,2.969 2.094,2.969 2.01,2.969 false 5.313,1.469 5.521,0.844 5.521,0.844 5.625,0.844 false 4.104,0.313 5.229,0.594 1.125,0.281 10 false Water Filler Cap 5.688,0.75 7.146,1.063 1.458,0.313 10 false Radiator Reserve Tank 4.896,2.229 5.521,2.458 0.625,0.229 10 false Radiator 4.74,2.729 5.99,2.927 1.25,0.198 10 false Radiator Drain Plug 0.688,2.885 2.104,3.365 1.417,0.479 10 false Cylinder Block Water Drain Cock Plug


b.

Remove the water filler cap.


c.

Loosen the cylinder block water drain cock plug.


d.

Drain the coolant from the reservoir tank.


e.

Tighten the radiator drain plug.


f.

Tighten the cylinder block water drain cock plug.

Torque:

13 N*m (130 kgf*cm, 9 ft.*lbf)



Hide 7.ADD ENGINE COOLANT

a.

Pour coolant into the radiator until it is full.

Capacity:

16.7 liters (17.6 US qts, 14.7 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:
·

Use of improper coolants may damage the engine cooling system.

·

Use only TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

·

New TOYOTA vehicles are filled with TOYOTA SLLC (color is pink, premixed ethylene glycol concentration is approximately 50 % and freezing temperature is -35°C (-31°F)). When replacing the coolant, TOYOTA SLLC is recommended.




b.

Check the coolant level inside the radiator by squeezing the inlet and outlet radiator hoses several times by hand. If the coolant level goes down, add coolant.


c.

Install the water filler cap securely.


d.
A156735

Slowly pour coolant into the radiator reservoir until it reaches the FULL line.


e.

Bleed air from the cooling system.

i.

Warm up the engine until the thermostat opens.

While the thermostat is open, circulate the coolant for several minutes.

HINT:

The thermostat open timing can be confirmed by pressing the inlet radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



ii.

Maintain the engine speed at 2500 to 3000 rpm.


iii.

Press the inlet and outlet radiator hoses several times by hand to bleed air.

CAUTION:

When pressing the radiator hoses:

·

Wear protective gloves.

·

Be careful as the radiator hoses are hot.

·

Keep your hands away from the radiator fan.





f.

Stop the engine and wait until the coolant cools down.


g.

Remove the water filler cap and check the coolant level inside the radiator.


h.

If the coolant level has dropped, add coolant until the radiator is full.


i.

Check the coolant level inside the radiator reservoir tank again. If it is below the full level, add coolant.


Hide 58420 9.INSTALL NO. 2 ENGINE SERVICE HOLE COVER ASSEMBLY

Hide 58734B 11.INSTALL REAR ENGINE SERVICE COVER WEATHERSTRIP

Hide 51405A 13.INSTALL NO. 1 ENGINE UNDER COVER