Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, Oil Control Valve (OCV) and VVT controller. The ECM sends a target "duty-cycle" control signal to the OCV. This control signal, applied to the OCV, regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed based on engine operation conditions, such as intake air volume, throttle position and engine coolant temperature.

The ECM controls the OCV based on the signals from several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative position between the camshaft and crankshaft is optimized, the engine torque and the fuel economy improve, and the exhaust emissions drop. The ECM detects the actual valve timing using signals from the camshaft position sensor and crankshaft position sensor. The ECM then performs feedback control and verifies target valve timing.

A103843E37
5.917,1.177 5.656,1.542 false 0.469,0.906 2.25,1.094 1.781,0.188 10 false Crankshaft Position Sensor 0.938,1.438 1.865,1.635 0.927,0.198 10 false MAF Meter 0.552,1.969 2.188,2.167 1.635,0.198 10 false Throttle Position Sensor 0.958,2.979 1.917,3.177 0.958,0.198 10 false ECT Sensor 0.625,3.5 2.083,3.698 1.458,0.198 10 false Vehicle Speed Signal 0.521,4.24 2.208,4.417 1.688,0.177 10 false Camshaft Position Sensor 3.604,1.302 4.927,1.531 1.323,0.229 10 false Target Valve Timing 3.938,3.188 4.74,3.396 0.802,0.208 10 false Correction 3.615,4.042 4.917,4.25 1.302,0.208 10 false Actual Valve Timing 4.073,0.219 4.49,0.417 0.417,0.198 10 false ECM 5.948,0.979 7.042,1.177 1.094,0.198 10 false Duty Control 5.885,2.969 6.958,3.51 1.073,0.542 10 false Camshaft Timing Oil Control Valve Assembly 4.531,2.5 5.385,2.698 0.854,0.198 10 false Feedback

DTC No. DTC Detection Condition Suspected Area
P0010 Open or short in oil control valve circuit
(1 trip detection logic)
·

Open or short in oil control valve circuit

·

Camshaft timing oil control valve assembly

·

ECM



MONITOR DESCRIPTION

After the ECM sends the "target" duty-cycle signal to the OCV, the ECM monitors the OCV current to establish an "actual" duty-cycle. The ECM detects a malfunction and sets a DTC when the actual duty-cycle ratio varies from the target duty-cycle ratio.

This monitor runs for 1 second (the first second of engine idle) after the engine is started.

WIRING DIAGRAM

A401740E01
0.448,2.042 0.781,2.219 0.333,0.177 10 false B72 0.448,2.219 3.281,2.438 2.833,0.219 10 false Camshaft Timing Oil Control Valve Assembly 1.5,0.854 1.646,1.031 0.146,0.177 10 false 2 1.5,1.583 1.646,1.76 0.146,0.177 10 false 1 1.292,0.875 1.438,1.052 0.146,0.177 10 false + 1.302,1.594 1.448,1.771 0.146,0.177 10 false - 5.438,0.854 5.917,1.042 0.479,0.188 10 false OC1+ 5.448,1.594 5.927,1.781 0.479,0.188 10 false OC1- 5.146,0.854 5.385,1.031 0.24,0.177 10 false 13 5.135,1.583 5.375,1.76 0.24,0.177 10 false 12 5.563,2.427 5.896,2.604 0.333,0.177 10 false B73 6,2.427 6.448,2.615 0.448,0.188 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR DTC
a.

Clear DTCs after recording the freeze frame data and DTCs (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).


b.

Allow the engine to idle and check for DTCs.


c.

Check whether P0010 is not present.

OK:

P0010 is not present.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY>INSPECTION).


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
a.

Disconnect the camshaft timing oil control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Check the resistance.

Standard Resistance:
Tester Connections Condition Specified Conditions
B72-2 (+) - B73-13 (OC1+) Always Below 1 Ω
B72-1 (-) - B73-12 (OC1-) Always Below 1 Ω
B72-2 (+) or B73-13 (OC1+) - Body ground Always 10 kΩ or higher
B72-1 (-) or B73-12 (OC1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR