Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0327  Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)  P0328  Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

The flat type knock sensor (non-resonant type) has a structure that can detect vibration in a wide band of frequency from about 6 to 15 kHz and has the following features:

·

The knock sensor is fitted on the cylinder block to detect engine knocking.

·

The sensor contains a piezoelectric element which generates voltage when it becomes deformed. This occurs when the cylinder block vibrates due to knocking. If engine knocking occurs, the ignition timing is retarded to suppress it.


DTC No. DTC Detection Condition Suspected Area
P0327 Output voltage of knock sensor is 0.5 V or less
(1 trip detection logic)
·

Short in knock sensor circuit

·

Knock sensor

·

ECM


P0328 Output voltage of knock sensor is 4.5 V or more
(1 trip detection logic)
·

Open in knock sensor circuit

·

Knock sensor

·

ECM



HINT:

When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

Reference: Inspection using an oscilloscope


A150243E30
0.333,0.51 1.896,0.719 1.563,0.208 10 false KNK1 Signal Waveform 2.615,1.927 2.969,2.135 0.354,0.208 10 false GND 2.396,1.188 2.958,1.396 0.563,0.208 10 false 1 V/DIV. 0.917,2.823 1.76,3.031 0.844,0.208 10 false 1 ms./DIV.

Tester Connection Tool Setting Condition Specified Condition
B73-29 (KNK1) - B73-30 (EKNK) 1 V/DIV.
1 ms./DIV.
Engine speed at 4000 rpm with warm engine The correct waveform is as shown

MONITOR DESCRIPTION

If the output signal remains low or high for more than 10 seconds, the ECM interprets this as a fault in the knock sensor and sets a DTC.

The monitor for DTC P0327 and P0328 runs after the engine is started and 5 seconds have passed.

WIRING DIAGRAM

A395986E01
0.281,2.052 0.594,2.25 0.313,0.198 10 false b1 0.292,2.229 1.271,2.427 0.979,0.198 10 false Knock Sensor 0.896,1.979 1.063,2.167 0.167,0.188 10 false 1 0.896,0.948 1.063,1.135 0.167,0.188 10 false 2 3.26,2.052 3.573,2.25 0.313,0.198 10 false Bb1 3.271,0.875 3.583,1.073 0.313,0.198 10 false Bb1 3.302,0.698 3.469,0.885 0.167,0.188 10 false 2 3.323,1.854 3.49,2.042 0.167,0.188 10 false 1 0.469,3.177 1.448,3.375 0.979,0.198 10 false *: Shielded 5.917,1.927 6.406,2.104 0.49,0.177 10 false EKNK 4.604,2.292 4.781,2.438 0.177,0.146 10 false * 5.938,0.76 6.427,0.938 0.49,0.177 10 false KNK1 5.635,0.75 5.844,0.927 0.208,0.177 10 false 29 5.635,1.927 5.844,2.104 0.208,0.177 10 false 30 5.927,2.688 6.188,2.854 0.26,0.167 10 false E1 6.104,3.188 6.438,3.365 0.333,0.177 10 false B73 6.104,3.365 6.531,3.563 0.427,0.198 10 false ECM 5.677,2.563 5.844,2.75 0.167,0.188 10 false 3

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT KNOCK SENSOR
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B73-29 - B73-30 (EKNK) 20°C (68°F) 120 to 280 kΩ



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM

NG

3.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
2.INSPECT ECM
a.
A161605E47
1.51,0.854 1.927,1.094 0.417,0.24 1.604,0.896 1.958,1.094 0.354,0.198 10 false Bb1 0.24,0.208 0.427,0.396 0.188,0.188 10 false *a 1.979,0.875 2.229,1.063 0.25,0.188 10 false *1

Disconnect the Bb1 connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Bb1 female connector 1 - 2 Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*1 Female
*a Front view of wire harness connector
(to ECM Wire)


Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR)
a.

Disconnect the ECM connector.


b.

Disconnect the knock sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b1-2 - B73-29 (KNK1) Always Below 1 Ω
b1-1 - B73-30 (EKNK) Always Below 1 Ω
b1-2 or B73-29 (KNK1) - Body ground Always 10 kΩ or higher
b1-1 or B73-30 (EKNK) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR