Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A"/"B" Correlation  


DESCRIPTION

In this system, the signals of the stop light switch's duplex system (STP and ST1-) are used to judge whether the brake system is abnormal or not. When the signals of depressing and releasing the brake pedal are detected simultaneously, the ECM interprets this as a malfunction of the stop light switch assembly.

Signal Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

HINT:

The normal condition of the signals is shown in the table above.


DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more:
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal is OFF when ST1- signal is OFF
·

Short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM



WIRING DIAGRAM

A401733E01
0.979,0.458 1.823,0.656 0.844,0.198 10 false from Battery 0.531,1.104 1.813,1.281 1.281,0.177 10 false from Ignition Switch 2.063,0.635 2.927,0.802 0.865,0.167 10 false STOP NO. 1 2.188,1.292 2.906,1.458 0.719,0.167 10 false IGN NO. 3 4.563,0.635 5.427,0.802 0.865,0.167 10 false STOP NO. 4 3.021,1.552 3.271,1.729 0.25,0.177 10 false H1 3.01,1.708 4.844,1.917 1.833,0.208 10 false Stop Light Switch Assembly 6.354,2.875 6.76,3.063 0.406,0.188 10 false ECM 6.177,1.125 6.542,1.313 0.365,0.188 10 false ST1- 6.177,0.354 6.542,0.542 0.365,0.188 10 false STP 6.188,2.198 6.469,2.385 0.281,0.188 10 false E1 5.823,2.208 6.115,2.396 0.292,0.188 10 false B73 5.823,1.125 6.146,1.313 0.323,0.188 10 false A55 5.823,0.469 6.146,0.656 0.323,0.188 10 false A53 2.833,0.344 2.958,0.542 0.125,0.198 10 false 1 3.75,0.99 3.875,1.188 0.125,0.198 10 false 4 2.844,0.99 2.969,1.188 0.125,0.198 10 false 3 3.75,0.354 3.875,0.552 0.125,0.198 10 false 2 5.906,0.271 6.031,0.469 0.125,0.198 10 false 4 5.906,2 6.031,2.198 0.125,0.198 10 false 3 5.885,0.917 6.083,1.104 0.198,0.188 10 false 16

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT STOP LIGHT (OPERATION)
a.

Check that the stop lights turn ON and OFF when the brake pedal is depressed and released, respectively.

OK:

Stop lights turn ON and OFF when brake pedal is depressed and released, respectively.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STP SIGNAL, ST1- VOLTAGE)

NG

REPAIR OR REPLACE STOP LIGHT SWITCH CIRCUIT

2.READ VALUE USING INTELLIGENT TESTER (STP SIGNAL, ST1- VOLTAGE)
a.
A430123E01
0.417,2.531 0.823,2.781 0.406,0.25 2.635,2.542 3.042,2.792 0.406,0.25 0.698,3.198 1,4.208 true 2.594,3.292 2.323,4.198 true 0.24,0.5 0.552,0.698 0.313,0.198 10 false *a 0.26,2.229 0.573,2.427 0.313,0.198 10 false *c 1.792,0.5 2.104,0.698 0.313,0.198 10 false *b 0.5,2.583 0.813,2.781 0.313,0.198 10 false B73 2.719,2.594 3.031,2.792 0.313,0.198 10 false A55 0.781,4.229 1.271,4.438 0.49,0.208 10 false 3 (E1) 2.063,4.229 2.771,4.458 0.708,0.229 10 false 16 (ST1-)

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.


d.

Check the STP signal when depressing and releasing the brake pedal.

OK:
Brake Pedal Condition Specified Condition
Depressed STP Signal ON
Released STP Signal OFF



e.

Measure the voltage of the ECM connectors.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A55-16 (ST1-) - B73-3 (E1) Depressed Below 1.5 V
A55-16 (ST1-) - B73-3 (E1) Released 7.5 to 14 V


Text in Illustration
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(to ECM)


Result:
Proceed to
OK
NG



OK

NG

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (Click here Vehicle Interior>LIGHTING>STOP LIGHT SWITCH>INSPECTION).


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the ECM connectors.


b.

Measure the voltage of the wire harness side connectors.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
A53-4 (STP) - Body ground Depressed 11 to 14 V
A53-4 (STP) - Body ground Released Below 1 V
A55-16 (ST1-) - Body ground Depressed Below 1 V
A55-16 (ST1-) - Body ground Released 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR