Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2118  Throttle Actuator Control Motor Current Range / Performance  


DESCRIPTION

The Electronic Throttle Control System (ETCS) has a dedicated power supply circuit. The voltage (+BM) is monitored and when it is low (below 4 V), the ECM determines that there is a malfunction in the electronic throttle control system and cuts off the current to the throttle actuator.

When the voltage becomes unstable, the electronic throttle control system itself becomes unstable. For this reason, when the voltage is low, the current to the throttle actuator is cut. If repairs are made and the system returns to normal, turn the ignition switch off. The ECM then allows the current to flow to the throttle actuator so that it can be restarted.

HINT:

This ETCS does not use a throttle cable.


A256705E11
0.083,1.802 0.917,2 0.833,0.198 10 false from Battery 0.833,3.552 1.917,3.75 1.083,0.198 10 false Throttle Actuator 4.75,1.708 5.146,1.896 0.396,0.188 10 false +BM 4.75,3.781 5.198,3.979 0.448,0.198 10 false ME01 4.75,2.448 5,2.667 0.25,0.219 10 false M+ 4.75,3.094 5,3.333 0.25,0.24 10 false M- 5.583,3.417 6.667,3.771 1.083,0.354 10 false Throttle Actuator Control Circuit 4.75,0.948 5,1.167 0.25,0.219 10 false +B 0.229,1.042 0.813,1.417 0.583,0.375 10 false from EFI Relay 5.448,1.542 6.76,1.906 1.313,0.365 10 false Power Source Circuit for CPU 1.219,1.979 1.667,2.167 0.448,0.188 10 false ETCS 5.583,4.24 6,4.5 0.417,0.26 10 false ECM

DTC No. DTC Detection Condition Suspected Area
P2118 Open in ETCS power source (+BM) circuit
(1 trip detection logic)
·

Open in ETCS power source circuit

·

Battery

·

Battery terminals

·

ETCS fuse

·

ECM



MONITOR DESCRIPTION

The ECM monitors the battery supply voltage applied to the throttle actuator.

When the power supply voltage (+BM) drops below 4 V for 0.8 seconds or more, the ECM interprets this as an open in the power supply circuit (+BM). The ECM illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored 5 seconds after the engine is next started.

FAIL-SAFE

When any of these DTCs as well as other DTCs relating to electronic throttle control system malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (+BM VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / +BM Voltage.


d.

Read the value displayed on the tester.


Result:
Result Proceed to
Below 11 V or higher than 14 V A
11 to 14 V B



A

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY, BODY GROUND)
a.
A146289E43
0.406,0.208 0.802,0.448 0.396,0.24 2.625,0.208 3.021,0.448 0.396,0.24 1.125,0.198 1.521,0.438 0.396,0.24 0.688,0.75 0.365,1.771 true 2.469,1.792 2.583,0.75 true 1.406,0.771 1.573,1.802 true 0.198,1.802 0.719,2 0.521,0.198 10 false 3 (E1) 2.229,1.813 2.885,2 0.656,0.188 10 false 7 (+BM) 0.479,0.25 0.813,0.438 0.333,0.188 10 false B73 0.146,0.094 0.427,0.271 0.281,0.177 10 false *a 2.698,0.25 3.031,0.438 0.333,0.188 10 false A55 1.208,0.229 1.542,0.417 0.333,0.188 10 false B75 1.333,1.833 1.99,2.021 0.656,0.188 10 false 3 (ME01)

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A55-7 (+BM) - Body ground Always 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-3 (ME01) - Body ground Always Below 1 Ω
B73-3 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR