Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P2119  Throttle Actuator Control Throttle Body Range / Performance  


DESCRIPTION

The Electronic Throttle Control System (ETCS) is composed of the throttle actuator, throttle position sensor, accelerator pedal position sensor, and ECM. The ECM operates the throttle actuator to regulate the throttle valve in response to driver inputs. The throttle position sensor detects the opening angle of the throttle valve, and provides the ECM with feedback so that the throttle valve can be appropriately controlled by the ECM.

DTC No. DTC Detection Condition Suspected Area
P2119 Throttle valve opening angle continues to vary greatly from target opening angle
(1 trip detection logic)
·

ETCS

·

ECM

·

Wire harness or connector



MONITOR DESCRIPTION

The ECM determines the actual opening angle of the throttle valve from the throttle position sensor signal. The actual opening angle is compared to the target opening angle calculated by the ECM. If the difference between these two values is outside the standard range, the ECM interprets this as a malfunction in the ETCS. The ECM then illuminates the MIL and stores the DTC.

If the malfunction is not repaired successfully, the DTC is stored when the accelerator pedal is quickly released (to close the throttle valve) after the engine speed reaches 5000 rpm by the accelerator pedal being fully depressed (fully opening the throttle valve).

FAIL-SAFE

When any of these DTCs as well as other DTCs relating to electronic throttle control system malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Refer to "Data List / Active Test" [Throttle Position Command, Throttle Position No. 1, Throttle Motor Current, Throttle Motor Duty (Open), Throttle Motor Duty (Close)] (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).



PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2119)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read DTCs.

Result:
Result Proceed to
DTC P2119 is output A
DTC P2119 and other DTCs are output B


HINT:

If any other DTCs besides P2119 are output, perform troubleshooting for those DTCs first.




A

2.READ VALUE USING GTS (THROTTLE POSITION)

B

2.READ VALUE USING GTS (THROTTLE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position Command.


g.

Read the values displayed on the GTS while fully depressing and releasing the accelerator pedal quickly.

Result:
Result Proceed to
Throttle Position No. 1 does not change A
Throttle Position No. 1 changes even a little B


HINT:

When a DTC is output, the system changes to fail-safe mode. Therefore, only use the data up until the time the DTC is stored for confirmation.




A

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)

B

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.
A059778E89
2.5,1.323 2.667,1.625 true 2.188,1.333 2.094,1.656 true 1.979,1.708 2.313,1.917 0.333,0.208 10 false M+ 2.667,1.656 2.948,1.927 0.281,0.271 10 false M- 0.167,0.115 0.417,0.323 0.25,0.208 10 false *a

Disconnect the throttle with motor body assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (M+) - 1 (M-) 20°C (68°F) 0.3 to 100 Ω


Text in Illustration
*a Component without harness connected
(Throttle with Motor Body Assembly)


Result:
Proceed to
OK
NG



OK

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

7.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for contamination between the throttle valve and the housing. If necessary, clean the throttle with motor body assembly. Also, check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (THROTTLE POSITION)

NG

7.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
5.READ VALUE USING GTS (THROTTLE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1, Throttle Position No. 2 and Throttle Position Command.


g.

Read the values displayed on the GTS while wiggling the ECM wire harness.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read DTCs.


Result:
Result Proceed to
Value in Data List changes when wire harness is wiggled, or DTC is output A
Other than above B



A

6.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)

B

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
6.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - THROTTLE WITH MOTOR BODY ASSEMBLY)
a.

As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).


Result:
Proceed to
NEXT



NEXT

END

7.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Replace the throttle with motor body assembly (Click here Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2119)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Start the engine.


g.

Allow the engine to idle for 20 seconds or more.


h.

Fully depress and release the accelerator pedal 3 times quickly (to fully open and close the throttle valve).


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P2119 is output B



A

END

B