Home › Engine / Hybrid System › 2TR-FE (ENGINE CONTROL) › SFI SYSTEM
RM2850E _51 Engine / Hybrid System _073287 2TR-FE ENGINE CONTROL _0357042 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the starter (ST) relay drive signal output from the ignition switch is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is input into the NE+ terminal. The ECM determines that the engine is cranked, and turns transistor in the ECM internal circuit on. Current flows to the circuit opening (C/OPN) relay by turning transistor on.

Then, the fuel pump operates.

While the NE signal is input into the ECM and the engine is running, the ECM turns transistor on continuously.

WIRING DIAGRAM

A401737E01
0.781,0.333 1.01,0.573 0.229,0.24 10 false 6 0.385,0.615 0.76,0.823 0.375,0.208 10 false AM1 0.969,0.344 1.354,0.552 0.385,0.208 10 false AM1 1.76,0.354 2.104,0.542 0.344,0.188 10 false IG1 2.083,0.354 2.313,0.594 0.229,0.24 10 false 5 2.573,0.271 2.802,0.51 0.229,0.24 10 false 6 2.531,0.458 2.844,0.698 0.313,0.24 10 false 2C 1.083,0.833 1.385,1.031 0.302,0.198 10 false J63 1.073,1 2.188,1.208 1.115,0.208 10 false Ignition Switch 0.396,1.188 0.958,1.406 0.563,0.219 10 false J/B ALT 0.385,1.875 0.771,2.083 0.385,0.208 10 false ALT 0.5,2.563 1.344,2.781 0.844,0.219 10 false R/B NO. 2-B 1.646,2.552 1.927,2.75 0.281,0.198 10 false P/I 2.979,1.031 3.708,1.219 0.729,0.188 10 false IG2 NO. 1 3.875,1.219 4.208,1.406 0.333,0.188 10 false IG2 4.646,0.26 4.875,0.5 0.229,0.24 10 false 7 4.604,0.458 4.885,0.698 0.281,0.24 10 false 2C 4.646,0.688 4.875,0.927 0.229,0.24 10 false 8 4.604,0.885 4.927,1.125 0.323,0.24 10 false 2C 5.052,1.604 5.771,1.833 0.719,0.229 10 false IGN NO.1 5.885,2.646 6.115,2.885 0.229,0.24 10 false 8 6.125,2.781 6.719,3 0.594,0.219 10 false MREL 6.135,4.521 6.427,4.76 0.292,0.24 10 false FC 5.823,4.531 6.052,4.771 0.229,0.24 10 false 25 6.438,5.052 6.76,5.24 0.323,0.188 10 false A55 6.427,5.219 6.844,5.448 0.417,0.229 10 false ECM 5.083,3.031 5.49,3.365 0.406,0.333 10 false FUEL PMP 4.625,2.219 4.854,2.458 0.229,0.24 10 false 4 4.604,2.417 4.896,2.646 0.292,0.229 10 false 2D 4.635,2.604 4.865,2.844 0.229,0.24 10 false 2 4.604,2.781 4.875,3.021 0.271,0.24 10 false 2D 4.625,3.49 4.854,3.729 0.229,0.24 10 false 1 4.583,3.677 5.063,3.927 0.479,0.25 10 false 2C 4.635,3.917 4.865,4.156 0.229,0.24 10 false 2 4.594,4.104 4.969,4.344 0.375,0.24 10 false 2C 4.625,4.448 4.906,4.677 0.281,0.229 10 false 3 4.594,4.646 4.99,4.958 0.396,0.313 10 false 2C 2.979,5.156 4.49,5.417 1.51,0.26 10 false NO. 2 Integration Relay 3.302,4.427 3.844,4.656 0.542,0.229 10 false C/OPN 2.552,2.208 2.781,2.448 0.229,0.24 10 false 1 2.521,2.417 2.844,2.667 0.323,0.25 10 false 2E 2.563,2.604 2.792,2.802 0.229,0.198 10 false 3 2.521,2.781 2.813,3 0.292,0.219 10 false 2D 2.563,3.49 2.792,3.729 0.229,0.24 10 false 4 2.531,3.677 2.823,3.917 0.292,0.24 10 false 2C 2.99,2.583 3.688,2.781 0.698,0.198 10 false EFI-MAIN 3.885,3.115 4.24,3.333 0.354,0.219 10 false EFI 0.385,3.531 1.146,3.76 0.76,0.229 10 false FL MAIN 0.583,4.094 0.813,4.281 0.229,0.188 10 false P7 0.583,4.271 1.354,4.521 0.771,0.25 10 false Fuel Pump 1.688,3.781 1.917,4.021 0.229,0.24 10 false 1 1.688,4.656 1.917,4.896 0.229,0.24 10 false 2 0.563,5.021 1.146,5.271 0.583,0.25 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS ON.


c.

Select the following menu items: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump/Speed.


d.

Check the operation of the relay while operating it using the GTS.

OK:

Fuel pump operating sound occurs.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (STARTER SIGNAL)

NG

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - ECM)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.


d.

Check the result when the ignition switch is turned to ON and START.

OK:
Ignition Switch Position Starter Signal
ON OFF
START ON



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ENGINE SPEED)

NG

REPAIR OR REPLACE STARTING SYSTEM

3.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.


d.

Read the values displayed on the GTS while cranking the engine.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT

4.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A55-25 (FC) - 2C-3 Always Below 1 Ω
A55-25 (FC) or 2C-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 2 INTEGRATION RELAY (C/OPN RELAY INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT NO. 2 INTEGRATION RELAY (C/OPN RELAY INPUT VOLTAGE)
a.
A318873E01
2.427,0.438 2.76,0.635 0.333,0.198 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 2.51,0.458 2.823,0.656 0.313,0.198 10 false 2C

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
2C-2 - Body ground Ignition switch off Below 1 V
2C-4 - Body ground
2C-2 - Body ground Ignition switch ON 11 to 14 V
2C-4 - Body ground Engine cranking


Text in Illustration
*a Component with harness connected
(NO. 2 Integration Relay)


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - NO. 2 INTEGRATION RELAY, BODY GROUND)

NG

8.INSPECT NO. 2 INTEGRATION RELAY (C/OPN RELAY)
6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - NO. 2 INTEGRATION RELAY, BODY GROUND)
a.

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P7-1 - 2C-4 Always Below 1 Ω
P7-2 - Body ground Always Below 1 Ω
P7-1 or 2C-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL PUMP
a.

Inspect the fuel pump (Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL PUMP>INSPECTION).


Result:
Proceed to
OK
NG



OK

NG

8.INSPECT NO. 2 INTEGRATION RELAY (C/OPN RELAY)
a.

Inspect the No. 2 integration relay (C/OPN relay) (Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - NO. 2 INTEGRATION RELAY)

NG

REPLACE NO. 2 INTEGRATION RELAY

9.CHECK HARNESS AND CONNECTOR (NO. 2 INTEGRATION RELAY - NO. 2 INTEGRATION RELAY)
a.

Remove the NO. 2 integration relay from the NO. 2 relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-8 - 2C-2 Always Below 1 Ω
2D-4 - 2C-1 Always Below 1 Ω
2C-8 or 2C-2 - Body ground Always 10 kΩ or higher
2D-4 or 2C-1 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR