Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM C

N04C-VL ENGINE CONTROL  ECD SYSTEM  P0107  Manifold Absolute Pressure / Barometric Pressure Circuit Low Input  P0108  Manifold Absolute Pressure / Barometric Pressure Circuit High Input  


DESCRIPTION

By a built-in sensor unit, the manifold absolute pressure sensor detects the intake manifold pressure as a voltage. The ECM then determines the basic injection duration and basic ignition advance angle based on this voltage.

Since the manifold absolute pressure sensor does not use the atmospheric pressure as a criterion, but senses the absolute pressure inside the intake manifold (the pressure in proportion to the preset absolute vacuum 0), it is not influenced by fluctuations in the atmospheric pressure due to high altitude and other factors. This permits it to control the air fuel ratio at the proper level under all conditions.

A208461E25
0.417,0.406 0.563,0.573 0.146,0.167 10 false V 0.365,0.813 0.583,0.969 0.219,0.156 10 false 4.5 0.219,1.896 0.604,2.052 0.385,0.156 10 false 0.345 1.031,2.292 1.25,2.49 0.219,0.198 10 false 93 2.323,2.292 2.635,2.531 0.313,0.24 10 false 370 0.896,2.656 1.292,2.979 0.396,0.323 10 false 698 (27.5) 2.885,2.479 3.323,2.823 0.438,0.344 10 false mmHg (in.Hg) 2.885,2.031 3.25,2.385 0.365,0.354 10 false kPa (abs) 2.271,2.656 2.615,2.99 0.344,0.333 10 false 2775 (109) 1.323,3.094 2.146,3.271 0.823,0.177 10 false Air Pressure 0.135,0.063 0.667,0.229 0.531,0.167 10 false Voltage

DTC No. DTC Detection Condition Trouble Area
P0107 2 seconds after engine is started, condition (a) continues for more than 0.5 seconds
(a) Short in manifold absolute pressure sensor circuit
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


P0108 2 seconds after engine is started, condition (a) continues for more than 0.5 seconds
(a) Open in manifold absolute pressure sensor circuit
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM



HINT:

If DTC P0107 or P0108 is detected, check the intake manifold pressure by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / MAP.

Intake Manifold Pressure (kPa) Malfunction
Approximately 0 Short in PIM and E2 circuit
255
·

Short in VC and PIM circuit

·

Open in PIM circuit

·

Open in E2 circuit




WIRING DIAGRAM

A398534E06
0.688,2.24 2.365,2.448 1.677,0.208 10 false Vacuum Sensor 0.698,2.073 1.156,2.271 0.458,0.198 10 false B18 5.917,2.063 6.375,2.26 0.458,0.198 10 false B104 5.927,2.313 6.385,2.51 0.458,0.198 10 false ECM 5.469,0.604 5.927,0.802 0.458,0.198 10 false VC 1.781,1.083 2.24,1.281 0.458,0.198 10 false PIM 5.469,1.083 5.927,1.281 0.458,0.198 10 false PIM 5.469,1.531 5.927,1.729 0.458,0.198 10 false E2 1.875,1.531 2.333,1.729 0.458,0.198 10 false E 1.854,0.604 2.313,0.802 0.458,0.198 10 false VC 2.156,0.5 2.313,0.698 0.156,0.198 10 false 3 2.167,0.99 2.323,1.188 0.156,0.198 10 false 2 2.167,1.438 2.323,1.635 0.156,0.198 10 false 1 5.198,0.51 5.406,0.708 0.208,0.198 10 false 13 5.25,0.979 5.406,1.177 0.156,0.198 10 false 5 5.188,1.427 5.406,1.625 0.219,0.198 10 false 14

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

If DTCs that are related to different systems are output simultaneously while terminal E2 is used as a ground terminal, terminal E2 may have an open circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.READ VALUE USING GTS (MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.


e.

Read the value.

OK:

Same value as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in altitude, pressure drops by 1 kPa. Varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmospheric Pressure" in the Data List.




Result:
Result Proceed to
NG A
OK B



A

2.INSPECT ECM (VC VOLTAGE)

B

2.INSPECT ECM (VC VOLTAGE)
a.
A403491E01
1.542,0.146 2.01,0.417 0.469,0.271 2.417,1.604 2.24,0.885 true 1.635,1.594 2.167,0.875 true 1.365,1.646 1.99,1.875 0.625,0.229 10 false 14 (E2) 2.219,1.635 2.885,1.896 0.667,0.26 10 false 13 (VC) 1.615,0.198 2.229,0.396 0.615,0.198 10 false B104 0.083,0.083 0.708,0.313 0.625,0.229 10 false *a

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B104-13 (VC) - B104-14 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B18-2 (PIM) - B104-5 (PIM) Always Below 1 Ω
B18-3 (VC) - B104-13 (VC) Always Below 1 Ω
B18-1 (E) - B104-14 (E2) Always Below 1 Ω
B18-2 (PIM) or B104-5 (PIM) - Body ground Always 10 kΩ or higher
B18-3 (VC) or B104-13 (VC) - Body ground Always 10 kΩ or higher
B18-1 (E) or B104-14 (E2) - Other terminal Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (PIM VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

4.INSPECT ECM (PIM VOLTAGE)
a.
A403491E03
1.542,0.146 2.01,0.417 0.469,0.271 2.417,1.604 2.198,0.875 true 1.635,1.594 1.927,0.729 true 1.365,1.635 1.99,1.865 0.625,0.229 10 false 5 (PIM) 2.208,1.625 2.875,1.885 0.667,0.26 10 false 14 (E2) 1.615,0.198 2.229,0.396 0.615,0.198 10 false B104 0.083,0.083 0.708,0.313 0.625,0.229 10 false *a

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B104-5 (PIM) - B104-14 (E2) Negative pressure of 93 kPa (698 mmHg, 27.5 in.Hg) applied 0.25 to 0.4 V
Positive pressure of 150 kPa (1125 mmHg, 44 in.Hg) applied 1.0 to 1.4 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG