Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM C

N04C-VL ENGINE CONTROL  ECD SYSTEM  P1674  Exhaust Brake VSV  


DESCRIPTION

The exhaust brake with bracket solenoid assembly, opens and closes according to the signals from the ECM. The ECM receives the signals from the exhaust retarder switch assembly. Through the exhaust brake with bracket solenoid assembly, the ECM controls the negative pressure applied to the exhaust retarder assembly.

DTC No. DTC Detection Condition Trouble Area
P1674 Open or short in exhaust brake solenoid circuit for more than 3 seconds with clutch pedal released
(1 trip detection logic)
·

Open or short in exhaust brake solenoid circuit

·

Exhaust brake with bracket solenoid assembly

·

ECM



WIRING DIAGRAM

A402321E04
0.583,2.396 0.896,2.594 0.313,0.198 10 false A4 0.573,2.573 2.344,2.948 1.771,0.375 10 false Exhaust Brake with Bracket Solenoid Assembly 5.938,2.771 6.427,2.948 0.49,0.177 10 false B102 5.948,2.958 6.333,3.146 0.385,0.188 10 false ECM 5.552,1.198 5.938,1.385 0.385,0.188 10 false EXB 5.563,1.906 5.802,2.094 0.24,0.188 10 false E1 5.313,1.083 5.469,1.281 0.156,0.198 10 false 3 5.313,1.771 5.469,1.969 0.156,0.198 10 false 1 2.063,1.083 2.219,1.281 0.156,0.198 10 false 1 2.063,1.781 2.219,1.979 0.156,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.INSPECT ECM (EXB VOLTAGE)
a.
A258701E08
2.823,0.135 3.313,0.427 0.49,0.292 3.25,0.708 3.083,1.677 true 3.063,0.719 2.427,1.677 true 2.906,0.198 3.344,0.438 0.438,0.24 10 false B102 0.073,0.052 0.24,0.208 0.167,0.156 10 false *a 2.25,1.719 2.781,1.917 0.531,0.198 10 false 3 (EXB) 2.896,1.708 3.313,1.917 0.417,0.208 10 false 1 (E1)

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B102-3 (EXB) - B102-1 (E1) Exhaust brake is operating 11 to 14 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

2.INSPECT EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY

NG

2.INSPECT EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY
a.
A217797E04
0.292,1.438 0.542,1.104 true 0.448,0.344 0.823,0.698 true 3,1.958 2.938,2.5 true 2.188,0.552 2.396,0.75 0.208,0.198 10 false *1 0.25,2.625 0.458,2.823 0.208,0.198 10 false *a 0.219,0.26 0.385,0.448 0.167,0.188 10 false *b 0.094,1.354 0.26,1.542 0.167,0.188 10 false *c 2.948,1.792 3.115,1.979 0.167,0.188 10 false *2

Remove the exhaust brake with bracket solenoid assembly.


b.

Check operation of the exhaust brake with bracket solenoid assembly.

OK:
Port Connection Condition Specified Condition
A - B Battery voltage is not applied Air does not flow
B - Air filter Air flows
A - B Battery voltage is applied to terminals 1 and 2 Air flows
B - Air filter Air does not flow


Text in Illustration
*1 Exhaust Brake with Bracket Solenoid Assembly
*2 Air Filter
*a Component without harness connected
(Exhaust Brake Solenoid)
*b Port A
*c Port B


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY)

NG

REPLACE EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (ECM - EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY)
a.

Disconnect the exhaust brake with bracket solenoid assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A4-1 - B102-3 (EXB) Always Below 1 Ω
A4-2 - Body ground Always Below 1 Ω
A4-1 or B102-3 (EXB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - EXHAUST BRAKE WITH BRACKET SOLENOID ASSEMBLY)