This is the repair procedure for the accelerator pedal position sensor.
This electrical throttle system does not use a throttle cable.
This accelerator pedal position sensor is non-contact type.
The accelerator pedal position sensor is mounted on the accelerator link assembly and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and a malfunction of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V, in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for engine control, and the VPA2 is a signal to indicate the information about the opening angle which is used for detecting a malfunction.
The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the injection volume based on these signals.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2120 | Condition (a) continues for 1 second or more:
(1 trip detection logic) (a) VPA less than 0.2 V and VPA2 greater than 2.7 deg, or VPA greater than 4.8 V |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
| P2121 | Either of following conditions (a) or (b) met:
(1 trip detection logic) (a) Difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V (learned value of accelerator off position) (b) Difference between VPA and VPA2 is greater than or equal to the specified valve |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
| P2122 | Conditions (a) and (b) continue for 1 second or more:
(1 trip detection logic) (a) VPA less than 0.2 V (b) VPA2 greater than 2.7 deg |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
| P2123 | Condition (a) continues for 2 seconds or more:
(1 trip detection logic) (a) VPA greater than 4.8 V |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
| P2125 | Condition (a) continues for 1 second or more:
(1 trip detection logic) (a) VPA2 less than 0.5 V and VPA greater than 2.7 deg, or VPA2 greater than 4.8 V and VPA greater than 0.2 V but less than 3.45 V |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
| P2127 | Conditions (a) and (b) continue for 1 second or more:
(1 trip detection logic) (a) VPA2 less than 0.5 V (b) VPA greater than 2.7 deg |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
| P2128 | Conditions (a) and (b) continue for 2 seconds or more:
(1 trip detection logic) (a) VPA2 greater than 4.8 V (b) VPA greater than 0.2 V but less than 3.45 V |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
| P2138 | Condition (a) or (b) continues for 2 seconds or more:
(1 trip detection logic) (a) Difference between VPA and VPA2 less than 0.02 V (b) VPA less than 0.2 V and VPA2 less than 0.5 V |
·
Open or short in accelerator pedal position sensor circuit ·
Accelerator pedal position sensor (built into accelerator link assembly) ·
ECM |
When DTC P2120, P2122, P2123, P2125, P2127, P2128 or P2138 is detected, check the output voltage of the accelerator pedal position sensor by entering the following menus on the GTS: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
| Trouble Area | Accelerator pedal position expressed as voltage output | |||
|---|---|---|---|---|
| Accelerator pedal released | Accelerator pedal depressed | |||
| Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 | |
| VC circuit open | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V | 0 to 0.2 V |
| VPA1 circuit open or ground short | 0 to 0.2 V | 1.4 to 1.8 V | 0 to 0.2 V | 3.6 to 4.4 V |
| VPA2 circuit open or ground short | 0.6 to 1.0 V | 0 to 0.2 V | 2.8 to 3.6 V | 0 to 0.2 V |
| EPA circuit open | 4.7 to 4.9 V | 4.7 to 4.9 V | 4.7 to 4.9 V | 4.7 to 4.9 V |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No. 1 and Accel Sensor Out No. 2.
Read the value.
| Accelerator Pedal Condition | Accel Sensor Out No. 1 | Accel Sensor Out No. 2 |
|---|---|---|
| Released | 0.6 to 1.0 V | 1.4 to 1.8 V |
| Depressed | 2.8 to 3.6 V | 3.6 to 4.4 V |
| *a | Depressed |
| *b | Released |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F9-2 (EPA2) - A56-3 (EPA2) | Always | Below 1 Ω |
| F9-1 (VPA2) - A57-1 (VPA2) | Always | Below 1 Ω |
| F9-4 (VCPA) - A56-6 (VCPA) | Always | Below 1 Ω |
| F9-3 (EPA) - A56-5 (EPA) | Always | Below 1 Ω |
| F9-5 (VPA) - A57-2 (VPA) | Always | Below 1 Ω |
| F9-2 (EPA2) or A56-3 (EPA2) - Body ground | Always | 10 kΩ or higher |
| F9-1 (VPA2) or A57-1 (VPA2) - Body ground | Always | 10 kΩ or higher |
| F9-4 (VCPA) or A56-6 (VCPA) - Body ground | Always | 10 kΩ or higher |
| F9-3 (EPA) or A56-5 (EPA) - Body ground | Always | 10 kΩ or higher |
| F9-5 (VPA) or A57-2 (VPA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal position sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A56-6 (VCPA) - A56-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A56-6 (VCPA) - A56-3 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Component with harness connected
(ECM) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator link assembly (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL).
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Run the engine at idle for 15 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P2120, P2121, P2122, P2123, P2125, P2127, P2128 or P2138 is output | A |
| DTC is not output | B |
A
B