Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 2 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357115 AIRBAG SYSTEM(for 2 Connectors Type) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 2 Connectors Type)  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the airbag ECU assembly, spiral cable sub-assembly and horn button assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1800/51 One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal 5 times in the driver side squib circuit during the primary check.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag ECU assembly malfunction.


·

Engine room main wire

·

Instrument panel wire

·

Spiral cable sub-assembly

·

Horn button assembly

·

Airbag ECU assembly


B1801/51 One of the following conditions is met:
·

The airbag ECU assembly detects an open circuit signal in the driver side squib circuit for 2 seconds.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag ECU assembly malfunction.


B1802/51 One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag ECU assembly malfunction.


B1803/51 One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

A horn button assembly malfunction.

·

A spiral cable sub-assembly malfunction.

·

An airbag ECU assembly malfunction.



WIRING DIAGRAM

C368509E01
1.802,0.521 2.063,0.698 0.26,0.177 10 false 2 1.802,1.354 2.063,1.531 0.26,0.177 10 false 1 3.063,1.354 3.323,1.531 0.26,0.177 10 false 2 3.083,0.5 3.344,0.677 0.26,0.177 10 false 1 2.771,0.5 3.031,0.677 0.26,0.177 10 false D+ 2.813,1.344 3.073,1.521 0.26,0.177 10 false D- 5.438,1.427 5.698,1.604 0.26,0.177 10 false D- 5.427,0.604 5.688,0.781 0.26,0.177 10 false D+ 4.104,0.375 4.365,0.552 0.26,0.177 10 false 4 4.104,1.219 4.365,1.396 0.26,0.177 10 false 3 5.219,1.344 5.479,1.521 0.26,0.177 10 false 6 5.208,0.51 5.469,0.688 0.26,0.177 10 false 5 4.073,0.823 4.333,1 0.26,0.177 10 false D+ 4.104,1.677 4.365,1.854 0.26,0.177 10 false D- 4.031,0.604 4.292,0.781 0.26,0.177 10 false AJ1 4.031,1.448 4.292,1.625 0.26,0.177 10 false AJ1 0.531,1.885 0.792,2.063 0.26,0.177 10 false z1 2.073,1.885 2.448,2.063 0.375,0.177 10 false J67 5.229,1.865 5.604,2.042 0.375,0.177 10 false A58 0.521,2.052 2.073,2.281 1.552,0.229 10 false Horn Button Assembly 2.063,2.052 3.063,2.396 1,0.344 10 false Spiral Cable Sub-assembly 5.229,2.042 6.885,2.271 1.656,0.229 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When installing the spiral cable sub-assembly and steering wheel, be sure to adjust the spiral cable sub-assembly as it may break if the steering wheel is turned before adjusting the spiral cable sub-assembly (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of roads (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK HORN BUTTON ASSEMBLY
a.

Turn the ignition switch off.

C373209E01
4.563,0.792 5,1.031 0.438,0.24 5.031,0.448 5.219,0.448 5.219,0.448 5.438,0.615 true 5.958,0.448 5.792,0.448 5.792,0.448 5.542,0.625 true 6.24,0.958 6.021,0.958 6.021,0.958 5.813,0.74 true 5.344,1.177 5.156,1.396 5.156,1.396 4.99,1.396 true 0.469,0.792 0.781,0.99 0.313,0.198 10 false *1 0.823,1.031 1.031,1.219 0.208,0.188 10 false H 0.99,1.031 1.198,1.219 0.208,0.188 10 false G 1.365,1.104 1.635,1.292 0.271,0.188 10 false *3 1.813,1.031 2.021,1.219 0.208,0.188 10 false F 1.948,1.031 2.156,1.219 0.208,0.188 10 false E 2.177,1.031 2.385,1.219 0.208,0.188 10 false D 2.333,1.031 2.542,1.219 0.208,0.188 10 false C 2.708,0.813 2.958,1 0.25,0.188 10 false A 2.844,1.115 3.125,1.302 0.281,0.188 10 false *2 4.375,0.094 4.656,0.281 0.281,0.188 10 false *a 5.406,0.156 5.688,0.344 0.281,0.188 10 false *4 4.667,0.365 5.135,0.573 0.469,0.208 10 false 1 (D-) 6,0.375 6.563,0.583 0.563,0.208 10 false 2 (D+) 4.698,0.823 4.969,1.01 0.271,0.188 10 false z1 6.302,0.896 6.615,1.083 0.313,0.188 10 false *5 4.813,1.313 5.125,1.5 0.313,0.188 10 false *b

Text in Illustration
*1 Horn Button Assembly *2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly *4 Connector G
*5 SST - -
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Orange


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Disconnect the connector from the horn button assembly.


d.

Connect the white wire of SST (resistance: 2.1 Ω) to connector G (orange connector).

CAUTION:

Never connect the tester to the horn button assembly for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


f.

Turn the ignition switch to ON, and wait at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait at least 60 seconds.


j.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


m.

Disconnect SST from connector G.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.
C373210E01
0.115,0.844 0.427,1.042 0.313,0.198 10 false *1 0.927,1.375 1.24,1.573 0.313,0.198 10 false *3 2.833,1.385 3.146,1.583 0.313,0.198 10 false *2 1.75,0.833 2.063,1.031 0.313,0.198 10 false *4 2.219,0.823 2.531,1.021 0.313,0.198 10 false *5 0.313,1.208 0.552,1.406 0.24,0.198 10 false H 0.521,1.208 0.74,1.406 0.219,0.198 10 false G 1.469,1.271 1.688,1.469 0.219,0.198 10 false F 1.656,1.271 1.875,1.469 0.219,0.198 10 false E 1.958,1.26 2.177,1.458 0.219,0.198 10 false D 2.167,1.26 2.385,1.458 0.219,0.198 10 false C 2.344,1.26 2.563,1.458 0.219,0.198 10 false B 2.656,1.021 2.875,1.219 0.219,0.198 10 false A

Disconnect the connector from the airbag ECU assembly, instrument panel wire and engine room main wire.


b.

Check that the connectors (on both sides of spiral cable sub-assembly, instrument panel wire and engine room main wire) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly
*4 Instrument Panel Wire
*5 Engine Room Main Wire


Result:
Proceed to
OK
NG



OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY OR INSTRUMENT PANEL WIRE OR ENGINE ROOM MAIN WIRE

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Connect the connector to the spiral cable sub-assembly, instrument panel wire and engine room main wire.


b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.

C373211E01
4.708,0.802 5.104,1.021 0.396,0.219 5.01,1.24 5.177,1.24 5.177,1.24 5.354,1.052 true 4.979,0.417 5.177,0.417 5.177,0.417 5.438,0.615 true 6.042,0.406 5.854,0.406 5.854,0.406 5.531,0.615 true 0.417,0.802 0.729,1 0.313,0.198 10 false *1 0.781,1.031 0.979,1.229 0.198,0.198 10 false H 0.948,1.031 1.146,1.229 0.198,0.198 10 false G 1.323,1.115 1.521,1.313 0.198,0.198 10 false *3 1.688,1.031 1.885,1.229 0.198,0.198 10 false F 1.833,1.031 2.031,1.229 0.198,0.198 10 false E 2.021,1.031 2.219,1.229 0.198,0.198 10 false D 2.156,1.031 2.354,1.229 0.198,0.198 10 false C 2.354,1.031 2.552,1.229 0.198,0.198 10 false B 2.719,0.802 2.917,1 0.198,0.198 10 false A 2.833,1.115 3.031,1.313 0.198,0.198 10 false *2 4.188,0.104 4.458,0.302 0.271,0.198 10 false *a 5.417,0.167 5.615,0.365 0.198,0.198 10 false *4 4.604,0.333 5.094,0.531 0.49,0.198 10 false 1 (D-) 6.073,0.333 6.563,0.531 0.49,0.198 10 false 2 (D+) 4.823,0.823 5.125,1.021 0.302,0.198 10 false z1 4.854,1.156 5.156,1.354 0.302,0.198 10 false *b

Text in Illustration
*1 Horn Button Assembly *2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly *4 Connector G
*a Front view of wire harness connector
(to Horn Button Assembly)
*b Color: Orange


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z1-2 (D+) - Body ground Ignition switch ON Below 1 V
z1-1 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - z1-1 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-2 (D+) - z1-1 (D-) Always 1 MΩ or higher
z1-2 (D+) - Body ground Always 1 MΩ or higher
z1-1 (D-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

5.CHECK DRIVER SIDE SQUIB CIRCUIT
4.CHECK FOR DTC
a.
C372839E01
0.073,1.031 0.385,1.229 0.313,0.198 10 false *1 0.469,1.271 0.698,1.469 0.229,0.198 10 false H 0.594,1.271 0.823,1.469 0.229,0.198 10 false G 1.042,1.385 1.354,1.583 0.313,0.198 10 false *3 1.698,1.292 1.896,1.5 0.198,0.208 10 false E 1.583,1.292 1.896,1.49 0.313,0.198 10 false F 1.969,1.292 2.25,1.5 0.281,0.208 10 false D 2.104,1.292 2.323,1.51 0.219,0.219 10 false C 2.552,1.031 2.75,1.25 0.198,0.219 10 false A 2.729,1.406 3.042,1.604 0.313,0.198 10 false *2

Connect the connectors to the horn button assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


c.

Turn the ignition switch to ON, and wait at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait at least 60 seconds.


g.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Horn Button Assembly
*2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly


Result:
Proceed to
OK
NG



OK

NG

5.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Disconnect the instrument panel wire connector from the spiral cable sub-assembly.

C372840E01
4.521,0.635 4.938,0.896 0.417,0.26 5.906,1.5 5.667,1.5 5.667,1.5 5.521,0.906 true 6.177,1.313 5.958,1.313 5.958,1.313 5.656,0.906 true 0.677,0.781 0.906,0.979 0.229,0.198 10 false *1 1.031,1.031 1.26,1.229 0.229,0.198 10 false H 1.229,1.031 1.458,1.229 0.229,0.198 10 false G 1.583,1.125 1.813,1.323 0.229,0.198 10 false *3 2.042,1.031 2.271,1.229 0.229,0.198 10 false F 2.229,1.021 2.458,1.219 0.229,0.198 10 false E 2.469,1.031 2.698,1.229 0.229,0.198 10 false D 2.604,1.031 2.833,1.229 0.229,0.198 10 false C 2.844,1.031 3.073,1.229 0.229,0.198 10 false B 2.667,0.635 2.896,0.833 0.229,0.198 10 false *5 2.313,0.635 2.542,0.833 0.229,0.198 10 false *4 4.375,0.115 4.667,0.323 0.292,0.208 10 false *a 4.625,0.677 4.99,0.896 0.365,0.219 10 false J67 5.354,0.219 5.719,0.438 0.365,0.219 10 false *6 6.219,1.229 6.76,1.448 0.542,0.219 10 false 1 (D+) 5.958,1.427 6.5,1.646 0.542,0.219 10 false 2 (D-) 3.167,0.781 3.396,0.979 0.229,0.198 10 false A 3.26,1.125 3.49,1.323 0.229,0.198 10 false *2

Text in Illustration
*1 Horn Button Assembly *2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly *4 Instrument Panel Wire
*5 Engine Room Main Wire *6 Connector E
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly)
- -


b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J67-1 (D+) - Body ground Ignition switch ON Below 1 V
J67-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J67-1 (D+) - J67-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J67-1 (D+) - J67-2 (D-) Always 1 MΩ or higher
J67-1 (D+) - Body ground Always 1 MΩ or higher
J67-2 (D-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

6.CHECK ENGINE ROOM MAIN WIRE
6.CHECK ENGINE ROOM MAIN WIRE
a.

Disconnect the engine room main wire connector from the instrument panel wire.

C372841E01
4.438,0.688 4.865,0.938 0.427,0.25 4.99,1.344 5.156,1.344 5.156,1.344 5.302,0.948 true 5,1.552 5.177,1.552 5.177,1.552 5.417,0.958 true 0.656,0.792 0.969,0.99 0.313,0.198 10 false *1 1.021,1.031 1.25,1.208 0.229,0.177 10 false H 1.219,1.031 1.448,1.208 0.229,0.177 10 false G 1.563,1.115 1.792,1.292 0.229,0.177 10 false *3 2.021,1.031 2.198,1.208 0.177,0.177 10 false F 2.198,1.031 2.375,1.208 0.177,0.177 10 false E 2.438,1.031 2.615,1.208 0.177,0.177 10 false D 2.615,1.031 2.792,1.208 0.177,0.177 10 false C 2.865,1.031 3.042,1.208 0.177,0.177 10 false B 2.688,0.646 2.865,0.823 0.177,0.177 10 false *4 3.156,0.802 3.365,0.979 0.208,0.177 10 false A 3.281,1.125 3.583,1.302 0.302,0.177 10 false *2 4.26,0.104 4.563,0.281 0.302,0.177 10 false *a 5.365,0.208 5.667,0.385 0.302,0.177 10 false *5 4.531,0.729 4.927,0.906 0.396,0.177 10 false AJ1 4.563,1.25 5.052,1.427 0.49,0.177 10 false 4 (D+) 4.604,1.479 5.094,1.656 0.49,0.177 10 false 3 (D-)

Text in Illustration
*1 Horn Button Assembly *2 Airbag ECU Assembly
*3 Spiral Cable Sub-assembly *4 Engine Room Main Wire
*5 Connector C - -
*a Rear view of wire harness connector
(to Instrument Panel Wire)
- -


b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AJ1-4 (D+) - Body ground Ignition switch ON Below 1 V
AJ1-3 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AJ1-4 (D+) - AJ1-3 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AJ1-4 (D+) - AJ1-3 (D-) Always 1 MΩ or higher
AJ1-4 (D+) - Body ground Always 1 MΩ or higher
AJ1-3 (D-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL WIRE

NG

REPLACE ENGINE ROOM MAIN WIRE