The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on or blinks* to inform the driver of the problem.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag ECU assembly in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to the normal voltage.
A malfunction in this circuit is not recorded in the airbag ECU assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
*: If the SRS warning light blinks, replace the airbag ECU assembly with a new one.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
If the DTC B1662/45 is output, troubleshoot the DTC first (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>B1662/45).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When trouble code B1662/45 is output, first perform troubleshooting for it.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Measure the voltage according to the value(s) in the table below.
11 to 14 V
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.
Check that the connectors are properly connected to the airbag ECU assembly and combination meter assembly.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag ECU assembly and combination meter assembly.
Check that the connectors (on the airbag ECU assembly side and combination meter assembly side) are not damaged.
The connectors are not deformed or damaged.
| *1 | Combination Meter Assembly |
| *2 | Airbag ECU Assembly |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-25 (E1) - Body ground | Always | Below 1 Ω |
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON, and wait at least 60 seconds.
Operate all the components of the electrical system (wipers, headlights, etc.).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A58-21 (IG2) - A58-25 (E1) | Ignition switch off | Below 1 V |
| A58-21 (IG2) - A58-25 (E1) | Ignition switch ON | 11 to 14 V |
| *a | Rear view of wire harness connector
(to Airbag ECU Assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-21 (ES) - Body ground | Always | Below 1 Ω |
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON, and wait at least 60 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J1-2 (IG+) - J1-21 (ES) | Ignition switch off | Below 1 V |
| J1-2 (IG+) - J1-21 (ES) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
| *1 | Combination Meter Assembly | *2 | Airbag ECU Assembly |
| *3 | Connector B | *4 | Connector C |
| *a | Rear view of wire harness connector
(to Airbag ECU Assembly) |
*b | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-14 (LA) - J1-40 (A/B) | Always | Below 1 Ω |
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON, and wait at least 60 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-14 (LA) - Body ground | Always | 1 MΩ or higher |
| J1-40 (A/B) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the combination meter assembly.
| *1 | Combination Meter Assembly | *2 | Airbag ECU Assembly |
| *3 | Connector B | *4 | Service Wire |
| *a | Rear view of wire harness connector
(to Airbag ECU Assembly) |
- | - |
Using a service wire, connect terminals 14 (LA) and 25 (E1) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON.
Check the SRS warning light condition.
The SRS warning light is not illuminated.
Turn the ignition switch off.
Disconnect the service wire from connector B.
Turn the ignition switch to ON.
Check the SRS warning light condition.
The SRS warning light is illuminated.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.
Temporarily replace the airbag ECU assembly with a new one (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG ECU>REMOVAL).
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON.
Check the SRS warning light condition.
After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.
The primary check period is approximately 6 seconds after the ignition switch is turned to ON.
| Proceed to |
|---|
| OK |
| NG |
OK
NG