Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 2 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357115 AIRBAG SYSTEM(for 2 Connectors Type) J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 2 Connectors Type)  SRS Warning Light does not Come ON  


CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:
·

When trouble code B1662/45 is output, first perform troubleshooting for it.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK BATTERY
a.

Measure the voltage according to the value(s) in the table below.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTORS

NG

REPLACE OR RECHARGE BATTERY

2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag ECU assembly and combination meter assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTOR PROPERLY

3.CHECK CONNECTORS
a.
C239134E04
0.865,1.375 1.177,1.573 0.313,0.198 10 false *1 2.26,1.375 2.573,1.573 0.313,0.198 10 false *2

Disconnect the connectors from the airbag ECU assembly and combination meter assembly.


b.

Check that the connectors (on the airbag ECU assembly side and combination meter assembly side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Combination Meter Assembly
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C287546E01
1.646,0.49 2.052,0.74 0.406,0.25 0.625,0.583 0.49,0.583 0.49,0.583 0.885,1.26 true 0.781,1.479 0.969,1.948 0.969,1.948 1.115,1.948 true 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.677,0.49 1.24,0.677 0.563,0.188 10 false 2 (IG+) 1.146,1.865 1.75,2.042 0.604,0.177 10 false 21 (ES) 1.781,0.531 2.083,0.708 0.302,0.177 10 false J1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-21 (ES) - Body ground Always Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


c.

Turn the ignition switch to ON, and wait at least 60 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J1-2 (IG+) - J1-21 (ES) Ignition switch off Below 1 V
J1-2 (IG+) - J1-21 (ES) Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIRBAG ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.

C373327E01
2.521,0.583 2.938,0.813 0.417,0.229 4.469,0.823 4.885,1.052 0.417,0.229 3.125,1.458 3.292,1.458 3.292,1.458 3.781,0.875 true 6.167,1.448 6.333,1.448 6.333,1.448 6.75,1.042 true 0.656,0.906 0.969,1.104 0.313,0.198 10 false D 0.573,1.26 0.885,1.458 0.313,0.198 10 false *1 1.938,1.271 2.25,1.469 0.313,0.198 10 false *2 1,1.125 1.24,1.323 0.24,0.198 10 false C 1.458,1.125 1.698,1.323 0.24,0.198 10 false B 1.75,0.917 1.99,1.115 0.24,0.198 10 false A 2.563,0.094 2.927,0.302 0.365,0.208 10 false *a 2.615,0.615 2.979,0.823 0.365,0.208 10 false A58 4.708,0.135 5.073,0.344 0.365,0.208 10 false *b 5.802,0.333 6.167,0.542 0.365,0.208 10 false *4 4.615,0.854 4.979,1.063 0.365,0.208 10 false J1 2.646,1.365 3.229,1.573 0.583,0.208 10 false 14 (LA) 5.635,1.344 6.26,1.552 0.625,0.208 10 false 40 (A/B) 3.552,0.125 3.917,0.333 0.365,0.208 10 false *3

Text in Illustration
*1 Combination Meter Assembly *2 Airbag ECU Assembly
*3 Connector B *4 Connector C
*a Rear view of wire harness connector
(to Airbag ECU Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-14 (LA) - J1-40 (A/B) Always Below 1 Ω



d.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


e.

Turn the ignition switch to ON, and wait at least 60 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A58-14 (LA) - Body ground Always 1 MΩ or higher
J1-40 (A/B) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SRS WARNING LIGHT

NG

REPLACE HARNESS AND CONNECTOR

6.CHECK SRS WARNING LIGHT
a.
B285673E01
0.881,1.336 1.058,1.505 0.177,0.17 10 *1 2.316,1.336 2.493,1.505 0.177,0.17 10 *2

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Connect the connector to the combination meter assembly.


d.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

The SRS warning light remains on.


Text in Illustration
*1 Combination Meter Assembly
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

7.CHECK AIRBAG ECU ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

7.CHECK AIRBAG ECU ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Temporarily replace the airbag ECU assembly with a new one (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG ECU>REMOVAL).


d.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

END (AIRBAG ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY