The front airbag sensor circuit consists of the airbag ECU assembly and front airbag sensor.
The front airbag sensor detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.
DTC B161C/9A or B161D/9A is stored when a malfunction is detected in the front airbag sensor circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B161C/9A
B161D/9A |
One of the following conditions is met:
·
The airbag ECU assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor circuit for 2 seconds. ·
A front airbag sensor malfunction. ·
An airbag ECU assembly malfunction. |
·
Engine room main wire ·
Cowl wire ·
Front airbag sensor ·
Airbag ECU assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
To perform the simulation method, wiggle each connector of the airbag system or drive the vehicle on various types of roads (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.
Check that the connectors are properly connected to the airbag ECU assembly and front airbag sensor.
The connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connectors from the airbag ECU assembly, front airbag sensor, cowl wire and engine room main wire.
Check that the connectors (on both sides of cowl wire and engine room main wire) are not damaged.
The connectors are not deformed or damaged.
| *1 | Front Airbag Sensor |
| *2 | Cowl Wire |
| *3 | Engine Room Main Wire |
| *4 | Airbag ECU Assembly |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the cowl wire and engine room main wire.
| *1 | Front Airbag Sensor | *2 | Airbag ECU Assembly |
| *3 | Connector E | *4 | Connector B |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Front Airbag Sensor) |
*b | Rear view of wire harness connector
(to Airbag ECU Assembly) |
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F10-2 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| F10-1 (-SL) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-2 (+SL) - F10-1 (-SL) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-2 (+SL) - F10-1 (-SL) | Always | 1 MΩ or higher |
| F10-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| F10-1 (-SL) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the airbag ECU assembly.
Temporarily replace the front airbag sensor with a new one (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT AIRBAG SENSOR>REMOVAL).
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON, and wait at least 60 seconds.
Clear the DTCs stored in memory (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait at least 60 seconds.
Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DTC CHECK / CLEAR).
DTC B161C/9A and B161D/9A are not output.
Codes other than DTCs B161C/9A and B161D/9A may be output at this time, but they are not related to this check.
| *1 | Front Airbag Sensor |
| *2 | Airbag ECU Assembly |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine room main wire connector from the cowl wire.
| *1 | Front Airbag Sensor | *2 | Cowl Wire |
| *3 | Engine Room Main Wire | *4 | Airbag ECU Assembly |
| *5 | Connector C | *6 | Connector B |
| *7 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Cowl Wire) |
*b | Rear view of wire harness connector
(to Airbag ECU Assembly) |
Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| AF1-2 (+SL) - Body ground | Ignition switch ON | Below 1 V |
| AF1-1 (-SL) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.
Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF1-2 (+SL) - AF1-1 (-SL) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| AF1-2 (+SL) - AF1-1 (-SL) | Always | 1 MΩ or higher |
| AF1-2 (+SL) - Body ground | Always | 1 MΩ or higher |
| AF1-1 (-SL) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG