Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 3 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357116 AIRBAG SYSTEM(for 3 Connectors Type) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 3 Connectors Type)  B1805/52  Short in Front Passenger Side Squib Circuit  B1806/52  Open in Front Passenger Side Squib Circuit  B1807/52  Short to GND in Front Passenger Side Squib Circuit  B1808/52  Short to B+ in Front Passenger Side Squib Circuit  


DESCRIPTION

The front passenger side squib circuit consists of the airbag ECU assembly and instrument panel passenger airbag assembly.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1805/52 One of the following conditions is met:
·

The airbag ECU assembly detects a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.

·

A front passenger side squib malfunction.

·

An airbag ECU assembly malfunction.


·

Engine room main wire

·

Instrument panel wire

·

No. 2 instrument panel wire

·

Instrument panel passenger airbag assembly

·

Airbag ECU assembly


B1806/52 One of the following conditions is met:
·

The airbag ECU assembly detects an open circuit signal in the front passenger side squib circuit for 2 seconds.

·

A front passenger side squib malfunction.

·

An airbag ECU assembly malfunction.


B1807/52 One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

An airbag ECU assembly malfunction.


B1808/52 One of the following conditions is met:
·

The airbag ECU assembly detects a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.

·

A front passenger side squib malfunction.

·

An airbag ECU assembly malfunction.



WIRING DIAGRAM

C372575E02
1.427,0.375 1.74,0.573 0.313,0.198 10 false P+ 1.438,1.135 1.75,1.333 0.313,0.198 10 false P- 2.906,1.417 3.219,1.615 0.313,0.198 10 false P- 4.167,1.417 4.479,1.615 0.313,0.198 10 false P- 5.583,1.24 5.896,1.438 0.313,0.198 10 false P- 2.875,0.646 3.188,0.844 0.313,0.198 10 false P+ 4.115,0.646 4.427,0.844 0.313,0.198 10 false P+ 5.573,0.469 5.885,0.667 0.313,0.198 10 false P+ 1.708,0.375 2.021,0.573 0.313,0.198 10 false 2 1.677,1.125 1.917,1.313 0.24,0.188 10 false 1 4.156,1.031 4.396,1.219 0.24,0.188 10 false 1 2.906,0.26 3.146,0.448 0.24,0.188 10 false 1 4.146,0.271 4.458,0.469 0.313,0.198 10 false 2 2.906,1.052 3.219,1.25 0.313,0.198 10 false 2 2.885,0.448 3.198,0.646 0.313,0.198 10 false Jf1 2.885,1.229 3.198,1.427 0.313,0.198 10 false Jf1 4.083,0.448 4.479,0.646 0.396,0.198 10 false AJ1 4.073,1.229 4.469,1.427 0.396,0.198 10 false AJ1 0.375,1.656 0.688,1.854 0.313,0.198 10 false f1 5.406,0.375 5.719,0.573 0.313,0.198 10 false 4 5.396,1.104 5.708,1.302 0.313,0.198 10 false 3 0.354,1.844 3.385,2.052 3.031,0.208 10 false Instrument Panel Passenger Airbag Assembly 5.354,1.875 7.094,2.104 1.74,0.229 10 false Airbag ECU Assembly 5.375,1.677 5.688,1.875 0.313,0.198 10 false A58

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB)
a.

Turn the ignition switch off.

C376995E01
4.177,0.667 4.594,0.896 0.417,0.229 4.688,0.219 4.875,0.219 4.875,0.219 5.208,0.458 true 5.865,0.219 5.677,0.219 5.677,0.219 5.365,0.458 true 6.094,1.031 5.927,1.031 5.927,1.031 5.656,0.729 true 5.76,1.313 5.594,1.313 5.594,1.313 5.292,1 true 0.99,0.5 1.302,0.698 0.313,0.198 10 false *1 1.396,0.729 1.635,0.917 0.24,0.188 10 false H 1.677,0.729 1.99,0.927 0.313,0.198 10 false G 1.927,0.74 2.24,0.938 0.313,0.198 10 false F 2.052,0.74 2.365,0.938 0.313,0.198 10 false E 2.271,0.74 2.583,0.938 0.313,0.198 10 false D 2.406,0.74 2.719,0.938 0.313,0.198 10 false C 2.771,0.51 3.083,0.708 0.313,0.198 10 false A 2.885,1.458 3.198,1.656 0.313,0.198 10 false *2 3.948,0.063 4.26,0.26 0.313,0.198 10 false *a 4.302,0.146 4.74,0.333 0.438,0.188 10 false 1 (P-) 5.188,0.021 5.49,0.219 0.302,0.198 10 false *3 5.927,0.146 6.5,0.375 0.573,0.229 10 false 2 (P+) 6.156,0.958 6.51,1.188 0.354,0.229 10 false *4 5.833,1.24 6.188,1.469 0.354,0.229 10 false *b 4.333,0.698 4.688,0.927 0.354,0.229 10 false f1

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly *2 Airbag ECU Assembly
*3 Connector G *4 SST
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Orange


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the instrument panel passenger airbag assembly.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector G (orange connector).

CAUTION:

Never connect the tester to the instrument panel passenger airbag assembly (front passenger side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector G.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connector from the airbag ECU assembly, No. 2 instrument panel wire, instrument panel wire and engine room main wire.


b.
C368516E01
0.083,0.635 0.396,0.833 0.313,0.198 10 false *1 0.844,0.417 1.156,0.615 0.313,0.198 10 false *3 1.427,0.427 1.74,0.625 0.313,0.198 10 false *4 2,0.427 2.313,0.625 0.313,0.198 10 false *5 2.573,0.625 2.885,0.823 0.313,0.198 10 false A 2.802,1.427 3.115,1.625 0.313,0.198 10 false *2 0.521,0.865 0.833,1.063 0.313,0.198 10 false H 0.75,0.865 1.063,1.063 0.313,0.198 10 false G 1.073,0.865 1.385,1.063 0.313,0.198 10 false F 1.323,0.865 1.635,1.063 0.313,0.198 10 false E 1.646,0.865 1.958,1.063 0.313,0.198 10 false D 1.875,0.865 2.188,1.063 0.313,0.198 10 false C 2.188,0.865 2.5,1.063 0.313,0.198 10 false B

Check that the connectors (on both sides of No. 2 instrument panel wire, instrument panel wire and engine room main wire) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Instrument Panel Passenger Side Squib
*2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire
*4 Instrument Panel Wire
*5 Engine Room Main Wire


Result:
Proceed to
OK
NG



OK

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT

NG

REPLACE INSTRUMENT PANEL WIRE OR NO. 2 INSTRUMENT PANEL WIRE OR ENGINE ROOM MAIN WIRE

3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.

Connect the connector to the No. 2 instrument panel wire, instrument panel wire and engine room main wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C368517E01
4.229,0.792 4.656,1.042 0.427,0.25 4.74,0.323 4.927,0.323 4.927,0.323 5.188,0.635 true 5.813,0.333 5.635,0.333 5.635,0.333 5.375,0.625 true 5.948,1.24 5.781,1.24 5.781,1.24 5.5,1.052 true 0.406,0.552 0.719,0.75 0.313,0.198 10 false *1 1.135,0.74 1.448,0.938 0.313,0.198 10 false G 0.854,0.74 1.167,0.938 0.313,0.198 10 false H 1.573,0.76 1.885,0.958 0.313,0.198 10 false E 1.458,0.76 1.771,0.958 0.313,0.198 10 false F 1.813,0.76 2.125,0.958 0.313,0.198 10 false D 1.938,0.76 2.25,0.958 0.313,0.198 10 false C 2.208,0.76 2.521,0.958 0.313,0.198 10 false B 2.667,0.552 2.979,0.75 0.313,0.198 10 false A 2.865,1.24 3.177,1.438 0.313,0.198 10 false *2 4.021,0.083 4.333,0.281 0.313,0.198 10 false *a 4.344,0.24 4.823,0.458 0.479,0.219 10 false 1 (P-) 5.229,0.104 5.531,0.313 0.302,0.208 10 false *3 5.875,0.26 6.417,0.469 0.542,0.208 10 false 2 (P+) 5.99,1.146 6.323,1.365 0.333,0.219 10 false *b 4.396,0.823 4.729,1.042 0.333,0.219 10 false f1

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly *2 Airbag ECU Assembly
*3 Connector G - -
*a Front view of wire harness connector
(to Instrument Panel Passenger Airbag Assembly)
*b Color: Orange


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
f1-2 (P+) - Body ground Ignition switch ON Below 1 V
f1-1 (P-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f1-2 (P+) - f1-1 (P-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
f1-2 (P+) - f1-1 (P-) Always 1 MΩ or higher
f1-2 (P+) - Body ground Always 1 MΩ or higher
f1-1 (P-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

5.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
4.CHECK FOR DTC
a.
C368520E01
0.302,0.615 0.615,0.813 0.313,0.198 10 false *1 0.698,0.865 1.01,1.063 0.313,0.198 10 false H 0.844,0.865 1.156,1.063 0.313,0.198 10 false G 1.115,0.865 1.427,1.063 0.313,0.198 10 false F 1.271,0.865 1.583,1.063 0.313,0.198 10 false E 1.552,0.865 1.865,1.063 0.313,0.198 10 false D 1.708,0.865 2.021,1.063 0.313,0.198 10 false C 2.167,0.635 2.479,0.833 0.313,0.198 10 false A 2.365,1.417 2.677,1.615 0.313,0.198 10 false *2

Connect the connectors to the instrument panel passenger airbag assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output.


HINT:

Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

NG

5.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT
a.

Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

C368518E01
4.479,0.646 4.875,0.896 0.396,0.25 4.771,1.281 4.938,1.281 4.938,1.281 5.26,1.052 true 6.021,1.302 5.875,1.302 5.875,1.302 5.563,1.073 true 0.406,0.552 0.719,0.75 0.313,0.198 10 false *1 0.854,0.75 1.125,0.948 0.271,0.198 10 false H 1.052,0.75 1.323,0.948 0.271,0.198 10 false G 1.354,0.76 1.625,0.958 0.271,0.198 10 false F 1.542,0.76 1.813,0.958 0.271,0.198 10 false E 1.802,0.76 2.073,0.958 0.271,0.198 10 false D 1.948,0.76 2.219,0.958 0.271,0.198 10 false C 2.219,0.76 2.49,0.958 0.271,0.198 10 false B 1.125,0.354 1.438,0.552 0.313,0.198 10 false *6 1.646,0.354 1.958,0.552 0.313,0.198 10 false *3 2.021,0.354 2.333,0.552 0.313,0.198 10 false *4 2.677,0.552 2.99,0.75 0.313,0.198 10 false A 2.875,1.25 3.188,1.448 0.313,0.198 10 false *2 4.333,0.104 4.646,0.302 0.313,0.198 10 false *a 5.302,0.177 5.615,0.375 0.313,0.198 10 false *5 4.594,0.698 4.906,0.896 0.313,0.198 10 false Jf1 4.365,1.188 4.896,1.385 0.531,0.198 10 false 1 (P+) 6.104,1.208 6.635,1.406 0.531,0.198 10 false 2 (P-)

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly *2 Airbag ECU Assembly
*3 Instrument Panel Wire *4 Engine Room Main Wire
*5 Connector E *6 No.2 Instrument Panel Wire
*a Front view of wire harness connector
(to No. 2 Instrument Panel Wire)
- -


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Jf1-1 (P+) - Body ground Ignition switch ON Below 1 V
Jf1-2 (P-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Jf1-1 (P+) - Jf1-2 (P-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 2 Connectors Type)>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Jf1-1 (P+) - Jf1-2 (P-) Always 1 MΩ or higher
Jf1-1 (P+) - Body ground Always 1 MΩ or higher
Jf1-2 (P-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE

NG

6.CHECK ENGINE ROOM MAIN WIRE
6.CHECK ENGINE ROOM MAIN WIRE
a.

Disconnect the engine room main wire connector from the instrument panel wire.

C368519E01
4.219,0.635 4.688,0.896 0.469,0.26 4.792,1.25 4.969,1.25 4.969,1.25 5.25,0.833 true 5.865,1.25 5.698,1.25 5.698,1.25 5.385,0.833 true 0.427,0.542 0.74,0.74 0.313,0.198 10 false *1 0.865,0.781 1.177,0.979 0.313,0.198 10 false H 1.052,0.781 1.365,0.979 0.313,0.198 10 false G 1.354,0.781 1.667,0.979 0.313,0.198 10 false F 1.542,0.781 1.854,0.979 0.313,0.198 10 false E 1.833,0.781 2.146,0.979 0.313,0.198 10 false D 2.052,0.771 2.365,0.969 0.313,0.198 10 false C 2.344,0.771 2.656,0.969 0.313,0.198 10 false B 2.656,0.542 2.969,0.74 0.313,0.198 10 false A 2.854,1.26 3.167,1.458 0.313,0.198 10 false *2 1.156,0.354 1.469,0.552 0.313,0.198 10 false *3 1.646,0.354 1.958,0.552 0.313,0.198 10 false *4 2.156,0.365 2.469,0.563 0.313,0.198 10 false *5 4.094,0.125 4.406,0.323 0.313,0.198 10 false *a 5.115,0.188 5.427,0.385 0.313,0.198 10 false *6 4.333,0.677 4.688,0.875 0.354,0.198 10 false AJ1 4.333,1.167 4.885,1.375 0.552,0.208 10 false 2 (P+) 5.927,1.156 6.479,1.365 0.552,0.208 10 false 1 (P-)

Text in Illustration
*1 Instrument Panel Passenger Airbag Assembly *2 Airbag ECU Assembly
*3 No. 2 Instrument Panel Wire *4 Instrument Panel Wire
*5 Engine Room Main Wire *6 Connector C
*a Rear view of wire harness connector
(to Instrument Panel Wire)
- -


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AJ1-2 (P+) - Body ground Ignition switch ON Below 1 V
AJ1-1 (P-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AJ1-2 (P+) - AJ1-1 (P-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AJ1-2 (P+) - AJ1-1 (P-) Always 1 MΩ or higher
AJ1-2 (P+) - Body ground Always 1 MΩ or higher
AJ1-1 (P-) - Body ground Always 1 MΩ or higher



j.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL WIRE

NG

REPLACE ENGINE ROOM MAIN WIRE