Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM (for 3 Connectors Type)
RM2850E _58 Vehicle Interior _073194 SUPPLEMENTAL RESTRAINT SYSTEMS _0357116 AIRBAG SYSTEM(for 3 Connectors Type) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(for 3 Connectors Type)  B1900/73  Short in Front Pretensioner Squib RH Circuit  B1901/73  Open in Front Pretensioner Squib RH Circuit  B1902/73  Short to GND in Front Pretensioner Squib RH Circuit  B1903/73  Short to B+ in Front Pretensioner Squib RH Circuit  


DESCRIPTION

The front pretensioner squib RH circuit consists of the airbag ECU assembly and front seat outer belt assembly RH.

This circuit signals the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front pretensioner squib RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1900/73 One of the following conditions is met:
·

The airbag ECU assembly detects line short circuit signal in front pretensioner squib RH circuit 5 times during primary check.

·

A front seat outer belt assembly RH malfunction.

·

An airbag ECU assembly malfunction.


·

Engine room main wire

·

Front seat outer belt assembly RH

·

Airbag ECU assembly


B1901/73 One of the following conditions is met:
·

The airbag ECU assembly detects open circuit signal in front pretensioner squib RH circuit for 2 seconds.

·

A front seat outer belt assembly RH malfunction.

·

An airbag ECU assembly malfunction.


B1902/73 One of the following conditions is met:
·

The airbag ECU assembly detects short circuit to ground signal in front pretensioner squib RH circuit for 0.5 seconds.

·

A front seat outer belt assembly RH malfunction.

·

An airbag ECU assembly malfunction.


B1903/73 One of the following conditions is met:
·

The airbag ECU assembly detects short circuit to B+ signal in front pretensioner squib RH circuit for 0.5 seconds.

·

A front seat outer belt assembly RH malfunction.

·

An airbag ECU assembly malfunction.



WIRING DIAGRAM

C401363E03
5.385,0.354 5.635,0.583 0.25,0.229 10 false 4 1.438,0.365 1.75,0.563 0.313,0.198 10 false R+ 1.448,1.125 1.76,1.323 0.313,0.198 10 false R- 1.708,0.365 1.958,0.594 0.25,0.229 10 false 1 5.396,1.125 5.646,1.354 0.25,0.229 10 false 5 1.708,1.125 1.958,1.354 0.25,0.229 10 false 2 5.594,0.458 6.021,0.656 0.427,0.198 10 false PR+ 5.292,1.667 5.719,1.865 0.427,0.198 10 false A59 5.302,1.875 6.875,2.104 1.573,0.229 10 false Airbag ECU Assembly 0.323,1.677 0.75,1.875 0.427,0.198 10 false A68 0.323,1.875 2.698,2.125 2.375,0.25 10 false Front Seat Outer Belt Assembly RH 5.594,1.229 6.021,1.427 0.427,0.198 10 false PR-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After replacing the airbag ECU assembly, refer to initialization (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of roads (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH
a.

Turn the ignition switch off.

C376996E01
4.333,0.698 4.75,0.969 0.417,0.271 4.688,0.313 4.865,0.313 4.865,0.313 5.167,0.635 true 5.802,0.333 5.604,0.333 5.604,0.333 5.25,0.646 true 6.042,0.979 5.823,0.979 5.823,0.979 5.51,0.802 true 1.104,0.917 1.417,1.115 0.313,0.198 10 false *1 1.521,1.125 1.833,1.323 0.313,0.198 10 false D 1.771,1.125 2.083,1.323 0.313,0.198 10 false C 2.417,1.188 2.729,1.385 0.313,0.198 10 false *2 2.333,0.906 2.646,1.104 0.313,0.198 10 false A 3.99,0.083 4.302,0.281 0.313,0.198 10 false *a 5.125,0.167 5.438,0.365 0.313,0.198 10 false *3 4.25,0.229 4.76,0.427 0.51,0.198 10 false 1 (R+) 5.885,0.271 6.396,0.469 0.51,0.198 10 false 2 (R-) 6.115,0.906 6.417,1.104 0.302,0.198 10 false *4 4.417,0.75 4.802,0.948 0.385,0.198 10 false A68

Text in Illustration
*1 Front Seat Outer Belt Assembly RH *2 Airbag ECU Assembly
*3 Connector C *4 SST
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)
- -


b.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


c.

Disconnect the connector from the front seat outer belt assembly RH.


d.

Connect the white wire of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat outer belt assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


f.

Turn the ignition switch to ON, and wait at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait at least 60 seconds.


j.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


m.

Disconnect SST from connector C.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.
C368521E01
0.469,1.281 0.781,1.479 0.313,0.198 10 false *1 0.979,1.5 1.292,1.698 0.313,0.198 10 false D 1.198,1.5 1.51,1.698 0.313,0.198 10 false C 1.573,1.5 1.885,1.698 0.313,0.198 10 false B 2.24,1.563 2.552,1.76 0.313,0.198 10 false *2 1.344,1.073 1.656,1.271 0.313,0.198 10 false *3 2,1.25 2.313,1.448 0.313,0.198 10 false A

Disconnect the connector from the airbag ECU assembly.


b.

Check that the connectors (on the front seat outer belt assembly RH side and airbag ECU assembly side) are not damaged.

OK:

The lock is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Front Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly
*3 Engine Room Main Wire


Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE ROOM MAIN WIRE

NG

REPLACE ENGINE ROOM MAIN WIRE

3.CHECK ENGINE ROOM MAIN WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.

C368522E01
4.219,0.792 4.615,1.042 0.396,0.25 4.604,0.396 4.75,0.396 4.75,0.396 5.01,0.792 true 5.688,0.427 5.479,0.427 5.479,0.427 5.188,0.792 true 0.813,1.031 1.125,1.229 0.313,0.198 10 false *1 1.427,1.281 1.74,1.479 0.313,0.198 10 false C 1.198,1.281 1.51,1.479 0.313,0.198 10 false D 1.76,1.281 2.073,1.479 0.313,0.198 10 false B 1.552,0.854 1.865,1.052 0.313,0.198 10 false *3 2.094,1.031 2.406,1.229 0.313,0.198 10 false A 2.292,1.323 2.604,1.521 0.313,0.198 10 false *2 4.063,0.073 4.375,0.271 0.313,0.198 10 false *a 5,0.229 5.313,0.427 0.313,0.198 10 false *4 4.177,0.333 4.688,0.521 0.51,0.188 10 false 1 (R+) 5.771,0.354 6.281,0.542 0.51,0.188 10 false 2 (R-) 4.292,0.823 4.802,1.01 0.51,0.188 10 false A68

Text in Illustration
*1 Front Seat Outer Belt Assembly RH *2 Airbag ECU Assembly
*3 Engine Room Main Wire *4 Connector C
*a Front view of wire harness connector
(to Front Seat Outer Belt Assembly RH)
- -


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A68-1 (R+) - Body ground Ignition switch ON Below 1 V
A68-2 (R-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-1 (R+) - A68-2 (R-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DIAGNOSIS SYSTEM)


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A68-1 (R+) - A68-2 (R-) Always 1 MΩ or higher
A68-1 (R+) - Body ground Always 1 MΩ or higher
A68-2 (R-) - Body ground Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

REPLACE ENGINE ROOM MAIN WIRE

4.CHECK FOR DTC
a.
C401566E01
0.51,0.958 0.823,1.156 0.313,0.198 10 false *1 0.99,1.229 1.302,1.427 0.313,0.198 10 false D 1.125,1.229 1.438,1.427 0.313,0.198 10 false C 1.646,0.948 1.958,1.146 0.313,0.198 10 false A 1.927,1.26 2.24,1.458 0.313,0.198 10 false *2

Connect the connectors to the front seat outer belt assembly RH and airbag ECU assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait at least 2 seconds.


c.

Turn the ignition switch to ON, and wait at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait at least 60 seconds.


g.

Check for DTCs (Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for 3 Connectors Type)>DTC CHECK / CLEAR).

OK:

DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output.


HINT:

Codes other than DTCs B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Outer Belt Assembly RH
*2 Airbag ECU Assembly


Result:
Proceed to
OK
NG



OK

NG