Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (w/ Brake pedal Load Sensing Switch) › 2017.01–2021.01
RM2850E _54 Brake _073264 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0358153 BRAKE ACTUATOR(w/ Brake pedal Load Sensing Switch) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/ Brake pedal Load Sensing Switch)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL BRAKE ACTUATOR ASSEMBLY WITH BRACKET

a.
C370898

Install the brake actuator assembly with bracket with the 4 bolts.

Torque:

19N*m ( 194kgf*cm , 14 ft.*lbf )


NOTICE:

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake lines because the brake actuator assembly is filled with brake fluid.



b.

Temporarily install the brake actuator assembly with bracket and the brake tube to the body with the 3 bolts.

NOTICE:

Do not bend or damage the brake tube.



c.
C370893E01
1.427,0.906 1.302,0.438 1.302,0.438 1.188,0.438 true 0.865,0.354 1.156,0.552 0.292,0.198 10 true SST 1.99,4.115 2.302,4.313 0.313,0.198 10 false *a

Using a SST and a union nut wrench, install the 4 brake line.

SST
09216-28010  (09216-02010)

Torque:
Specified tightening torque:

15N*m ( 155kgf*cm , 11 ft.*lbf )


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + SST (fulcrum length of 82 mm (3.228 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 11 N*m (115 kgf*cm, 8 ft.*lbf)



Text in Illustration
*a Torque Wrench Fulcrum Length


d.
C370904E01
0.635,2.375 0.948,2.573 0.313,0.198 10 false *a

Using a union nut wrench, install the 4 brake line.

Text in Illustration
*a Torque Wrench Fulcrum Length

Torque:

24N*m ( 245kgf*cm , 18 ft.*lbf )


NOTICE:
·

Do not allow any foreign matter such as dirt or dust to enter the connectors of the brake tube.

·

Do not bend or damage the brake tube.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 23 N*m (229 kgf*cm, 17 ft.*lbf)




e.

Attach the harness clamp.


f.

Connect the connector and lock the lock lever.

NOTICE:
·

Check that the lock lever is securely locked.

·

Before connecting the connectors, make sure that the connector faces (including the inside) are free of water, oil and foreign matter.




Hide 3.INSTALL FRONT WHEEL

Hide 4.ADD BRAKE FLUID

Hide 7. YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION