Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0500  Vehicle Speed Sensor "A" Circuit  


DESCRIPTION

The combination meter assembly sends the vehicle speed signal to the transmission control ECU assembly, and based on this, gear shifting and lock-up control are performed.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0500 Vehicle Speed Sensor "A" Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Vehicle running (Transmission revolution sensor (NC) is normal)

2.

SPD1 signal not input while transmission revolution sensor (NC) signal is input

3.

-

4.

2 trip detection logic


·

Wire harness or connector (Speed Signal Circuit)

·

Combination meter assembly

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Perform the D Position Shift Test inspection in Road Test.*1

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (*1) again.


WIRING DIAGRAM

C421140E02
4.771,0.906 5.083,1.104 0.313,0.198 10 false 13 4.698,1.135 5.313,1.333 0.615,0.198 10 false B134 4.688,1.865 5.302,2.063 0.615,0.198 10 false B133 4.813,1.625 4.969,1.823 0.156,0.198 10 false 8 5.125,1.854 5.438,2.052 0.313,0.198 10 false E 5.094,1.01 5.708,1.208 0.615,0.198 10 false SPD1 1.729,1.01 2.042,1.208 0.313,0.198 10 false +S 2.042,1.01 2.198,1.208 0.156,0.198 10 false 6 0.396,1.948 0.708,2.146 0.313,0.198 10 false J1 0.385,2.115 4.365,2.313 3.979,0.198 10 false Combination Meter Assembly 3.552,3.125 4.604,3.323 1.052,0.198 10 false to Other ECUs 5.26,2.417 6.604,2.802 1.344,0.385 10 false Transmission Control ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
HINT:

Drive the vehicle and check whether the operation of the speedometer is normal.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List / Vehicle Speed.


e.

Drive the vehicle.

CAUTION:

Strictly observe posted speed, limits, traffic laws and road conditions.



f.

According to the display on the GTS, read the Data List.


OK:

Vehicle speeds displayed on GTS and speedometer display are equal.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (CHECK WAVEFORM)
2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (CHECK WAVEFORM)
CAUTION:

Strictly observe posted speed, limits, traffic laws and road conditions.


a.
C373908C01
1.74,0.344 2.125,0.583 0.385,0.24 2.167,0.344 2.552,0.583 0.385,0.24 1.833,1.708 2.104,1.188 true 2.75,1.719 2.531,1.281 true 1.781,0.396 2.125,0.573 0.344,0.177 10 false B133 2.208,0.396 2.552,0.573 0.344,0.177 10 false B134 1.708,1.771 2.156,1.948 0.448,0.177 10 false 8 (E) 2.479,1.75 3.219,1.927 0.74,0.177 10 false 13 (SPD1) 2.958,3.5 3.302,3.677 0.344,0.177 10 false GND 0.125,0.135 0.469,0.313 0.344,0.177 10 false *a
*a Component with harness connected
(Transmission Control ECU Assembly)


Connect an oscilloscope between the transmission control ECU assembly terminals specified in the table below.

Item Content
Terminal SPD1 - E
Tool setting 2 V/DIV, 20 ms/DIV
Vehicle conditions Vehicle speed 20 km/h (12 mph)

HINT:

The wavelength shortens as the vehicle speed increases.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TRANSMISSION CONTROL ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-6 (+S) - B134-13 (SPD1) Always Below 1 Ω
J1-6 (+S) or B134-13 (SPD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR