Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0706  Transmission Range Sensor "A" Circuit Range/Performance  


DESCRIPTION

There are No. 8 oil pressure switches installed inside the valve body. The operation of each solenoid, shift valve, control valve, etc. changes the oil path inside the valve, which causes each oil pressure switch to change between on and off. The No. 8 oil pressure switch operates based on the D position pressure status. When there is a malfunction in the TPS8 signal system or valve body system, the transmission control ECU assembly stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0706 Transmission Range Sensor "A" Circuit Range/Performance 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
DTC Detection Condition 1:
1.

Shift lever in D, 4 or 2/L

2.

No. 8 oil pressure switch off

3.

Continues for 7 seconds or more, 3 times consecutively

4.

1 trip detection logic


DTC Detection Condition 2:
1.

Shift lever in P, R or N, engine running

2.

No. 8 oil pressure switch on

3.

0.5 seconds or more

4.

1 trip detection logic


·

Wire harness or connector (TPS8 signal circuit)

·

No. 1 Transmission Wire

·

No. 8 oil pressure switch

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Start the engine.

2.

Set the parking brake and keep the brake pedal depressed firmly.

3.

Wait for 7 seconds or more with the shift lever in D, and then move the shift lever to P.*1

4.

Perform step (*1) 3 times.


WIRING DIAGRAM

C372557E03
1.292,1.219 2.979,1.552 1.688,0.333 10 false No. 8 Oil Pressure Switch 0.938,1.76 1.344,1.969 0.406,0.208 10 false B137 0.938,1.917 3.146,2.292 2.208,0.375 10 false No. 1 Transmission Wire 5.063,2.167 6.406,2.615 1.344,0.448 10 false Transmission Control ECU Assembly 4.708,0.896 5.104,1.094 0.396,0.198 10 false B132 4.708,1.677 5.104,1.875 0.396,0.198 10 false B133 2.865,0.781 3.25,0.938 0.385,0.156 10 false TPS8 3.323,0.781 3.469,0.948 0.146,0.167 10 false 6 5.135,0.781 5.521,0.938 0.385,0.156 10 false TPS8 5.156,1.667 5.323,1.844 0.167,0.177 10 false E 4.823,1.458 4.99,1.635 0.167,0.177 10 false 8 4.771,0.688 4.99,0.865 0.219,0.177 10 false 26

CAUTION / NOTICE / HINT

NOTICE:

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


HINT:
·

Refer to Parts Location for the location of each shift solenoid valve and each oil pressure switch.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>PARTS LOCATION

·

Use a new transmission wire if the pin and socket terminals are removed on each oil pressure switch.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 TRANSMISSION WIRE - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the No. 1 transmission wire connector.


b.

Disconnect the transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B137-6 (TPS8) - B132-26 (TPS8) Always Below 1 Ω
B137-6 (TPS8) or B133-26 (TPS8) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 8 OIL PRESSURE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 8 OIL PRESSURE SWITCH
a.

Start the engine.


b.
C233571C06
0.948,0.563 1.344,0.833 0.396,0.271 1.708,0.563 2.104,0.833 0.396,0.271 1.25,1.479 1.094,1.865 true 2.115,1.354 2.25,1.885 true 0.083,0.073 0.271,0.219 0.188,0.146 10 false *a 0.99,0.615 1.375,0.781 0.385,0.167 10 false B132 1.76,0.615 2.167,0.781 0.406,0.167 10 false B133 0.854,1.917 1.531,2.083 0.677,0.167 10 false 26 (TPS8) 2.188,1.938 2.594,2.104 0.406,0.167 10 false 8 (E)
*a Component with harness connected
(Transmission Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B132-26 (TPS8) - B133-8 (E)
·

Engine idling speed

·

Shift lever in P

·

No. 8 oil pressure switch off


11 to 14 V
·

Engine idling speed

·

Shift lever in D

·

No. 8 oil pressure switch on


Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

3.INSPECT NO. 1 TRANSMISSION WIRE
3.INSPECT NO. 1 TRANSMISSION WIRE

b.
C365245C03
1.865,2.625 2.104,2.896 true 2.458,1.052 2.781,1.479 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *1 1.969,2.958 2.583,3.156 0.615,0.198 10 false TPS8 2.667,1.542 3.281,1.74 0.615,0.198 10 false TPS8
*1 No. 1 Transmission Wire


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (TPS8) - TPS8 No. 8 oil pressure switch side Always Below 1 Ω
6 (TPS8) or TPS8 No. 8 oil pressure switch side - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE NO. 8 OIL PRESSURE SWITCH AND NO. 1 TRANSMISSION WIRE

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT SOLENOID VALVE>REMOVAL

HINT:

Use a new transmission wire if the pin and socket terminals are removed on each oil pressure switch.



NG