Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0715  Input/Turbine Shaft Speed Sensor "A" Circuit  


DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input speed of the transmission. By comparing the speed sensor (NT) signal with the transmission revolution sensor (NC) signal, the transmission control ECU assembly controls engine torque and shift timing. Based on the input turbine speed and the engine speed signal, lock-up control is performed.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0715 Input/Turbine Shaft Speed Sensor "A" Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Vehicle is being driven (Shift lever not in P or N position)

2.

Turbine rotation speed signal not input

3.

-

4.

2 trip detection logic


·

Wire harness or connector (Speed sensor (NT) signal circuit)

·

Speed sensor (NT)

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Perform the D Position Shift Test inspection in Road Test.*1

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (*1) again.


WIRING DIAGRAM

C421141E02
1.771,1.115 2.115,1.271 0.344,0.156 10 false NTB 1.76,2.26 2.104,2.417 0.344,0.156 10 false NTO 5.271,2.135 5.615,2.292 0.344,0.156 10 false NTO 5.26,1.01 5.604,1.167 0.344,0.156 10 false NCB 4.844,1.115 5.26,1.302 0.417,0.188 10 false B133 4.844,2.24 5.271,2.427 0.427,0.188 10 false B134 4.969,0.896 5.125,1.094 0.156,0.198 10 false 1 4.969,2.021 5.125,2.219 0.156,0.198 10 false 1 2.198,2.125 2.354,2.323 0.156,0.198 10 false 1 2.188,0.99 2.344,1.188 0.156,0.198 10 false 2 1,2.698 1.427,2.896 0.427,0.198 10 false B130 0.99,2.844 2.313,3.052 1.323,0.208 10 false Speed Sensor (NT) 5.063,3.063 6.396,3.448 1.333,0.385 10 false Transmission Control ECU Assembly 4.854,2.76 5.271,2.948 0.417,0.188 10 false B133 4.979,2.521 5.135,2.719 0.156,0.198 10 false 8 5.26,2.76 5.573,2.958 0.313,0.198 10 false E

CAUTION / NOTICE / HINT

NOTICE:

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


PROCEDURE

1.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NCB TERMINAL VOLTAGE)
a.

Start the engine.


b.
C233571C07
1.708,0.563 2.104,0.833 0.396,0.271 2.115,1.26 2.594,1.833 true 2.115,1.354 1.76,1.865 true 0.083,0.073 0.271,0.219 0.188,0.146 10 false *a 1.74,0.615 2.125,0.792 0.385,0.177 10 false B133 2.438,1.885 3.073,2.073 0.635,0.188 10 false 1 (NCB) 1.667,1.896 2.073,2.073 0.406,0.177 10 false 8 (E)
*a Component with harness connected
(Transmission Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B133-1 (NCB) - B133-8 (E) Engine idling speed 6 to 10 V



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NTO TERMINAL WAVEFORM)

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NT) - TRANSMISSION CONTROL ECU ASSEMBLY)
2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NTO TERMINAL WAVEFORM)
a.
C239962C02
2.208,0.385 2.604,0.635 0.396,0.25 1.708,0.385 2.115,0.625 0.406,0.24 2.115,1.177 1.948,1.719 true 2.531,1.094 2.729,1.708 true 0.115,0.083 0.417,0.323 0.302,0.24 10 false *a 2.25,0.438 2.615,0.635 0.365,0.198 10 false B134 1.75,0.438 2.135,0.604 0.385,0.167 10 false B133 1.833,1.75 2.271,1.958 0.438,0.208 10 false 8 (E) 2.563,1.74 3.146,1.948 0.583,0.208 10 false 1 (NTO) 2.99,3.99 3.333,4.167 0.344,0.177 10 false GND
*a Component with harness connected
(Transmission Control ECU Assembly)


Connect an oscilloscope between the transmission control ECU assembly terminals specified in the table below.

Item Content
Terminal NTO - E
Tool setting 500 mV/DIV, 0.5 ms/DIV
Vehicle conditions Engine idling

HINT:

The wavelength shortens as the turbine speed increases.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NT) - TRANSMISSION CONTROL ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (SPEED SENSOR (NT) - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the speed sensor (NT) connector.


b.

Disconnect the transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B130-2 (NTB) - B133-1 (NCB) Always Below 1 Ω
B130-1 (NTO) - B133-1 (NTO) Always Below 1 Ω
B130-2 (NTB) - Body ground Always 10 kΩ or higher
B130-1 (NTO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR