Home › Drivetrain › A861E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2019.08
RM2850E _52 Drivetrain _082622 A861E AUTOMATIC TRANSMISSION / TRANSAXLE _0398655 AUTOMATIC TRANSMISSION SYSTEM C

A861E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0720  Output Shaft Speed Sensor Circuit  


DESCRIPTION

The transmission revolution sensor (NC) detects the rotation speed of the transmission output shaft and sends signals to the transmission control ECU assembly. Based on the transmission revolution sensor (NC) signal and the speed sensor (NT) signal, the transmission control ECU assembly controls engine torque and shift timing.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0720 Output Shaft Speed Sensor Circuit 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Shift lever not in P or N position (SPD1 signal is normally)

2.

NC signal is not input when SPD1 signal is input

3.

-

4.

2 trip detection logic


·

Wire harness or connector (Transmission revolution sensor NC signal circuit)

·

Transmission revolution sensor (NC)

·

Transmission control ECU assembly


O/D OFF Indicator Light: Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


1.

Perform the D Position Shift Test inspection in Road Test.*1

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (*1) again.


WIRING DIAGRAM

C421142E02
1.771,1.104 2.115,1.271 0.344,0.167 10 false NCB 1.76,2.229 2.104,2.396 0.344,0.167 10 false NCO 5.281,2.135 5.625,2.302 0.344,0.167 10 false NCO 5.26,1 5.604,1.167 0.344,0.167 10 false NCB 0.75,2.667 1.219,2.833 0.469,0.167 10 false B139 0.75,2.833 2.25,3.219 1.5,0.385 10 false Transmission Revolution Sensor (NC) 4.635,3.083 5.115,3.25 0.479,0.167 10 false B133 5.021,3.073 6.354,3.573 1.333,0.5 10 false Transmission Control ECU Assembly 2.198,1 2.354,1.198 0.156,0.198 10 false 2 5.031,2.135 5.188,2.333 0.156,0.198 10 false 2 5.042,0.99 5.198,1.188 0.156,0.198 10 false 1 2.188,2.135 2.344,2.333 0.156,0.198 10 false 1 5.281,2.677 5.594,2.875 0.313,0.198 10 false E 5.021,2.542 5.177,2.74 0.156,0.198 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Perform initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>A861E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION


PROCEDURE

1.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NCB TERMINAL VOLTAGE)
a.

Start the engine.


b.
C233571C07
1.708,0.563 2.104,0.833 0.396,0.271 2.115,1.26 2.594,1.833 true 2.115,1.354 1.76,1.865 true 0.083,0.073 0.271,0.219 0.188,0.146 10 false *a 1.74,0.615 2.125,0.792 0.385,0.177 10 false B133 2.438,1.885 3.073,2.073 0.635,0.188 10 false 1 (NCB) 1.667,1.896 2.073,2.073 0.406,0.177 10 false 8 (E)
*a Component with harness connected
(Transmission Control ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B133-1 (NCB) - B133-8 (E) Engine idling speed 6 to 10 V



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NCO TERMINAL WAVEFORM)

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NC) - TRANSMISSION CONTROL ECU ASSEMBLY)
2.INSPECT TRANSMISSION CONTROL ECU ASSEMBLY (NCO TERMINAL WAVEFORM)
CAUTION:

Strictly observe posted speed, limits, traffic laws and road conditions.


a.
C372848C01
1.729,0.302 2.125,0.542 0.396,0.24 1.688,1.76 2.052,1.094 true 2.385,1.75 2.115,1.198 true 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 3.052,3.906 3.365,4.104 0.313,0.198 10 false GND 1.458,1.813 2.042,2.021 0.583,0.208 10 false 2 (NCO) 2.333,1.802 2.76,2.031 0.427,0.229 10 false 8 (E) 1.771,0.354 2.229,0.552 0.458,0.198 10 false B133
*a Component with harness connected
(Transmission Control ECU Assembly)


Connect an oscilloscope between the transmission control ECU assembly terminals specified in the table below.

Item Content
Terminal NCO - E
Tool setting 500 mV/DIV, 2 ms/DIV
Vehicle conditions Vehicle speed 20 km/h (12 mph)

HINT:

The wavelength shortens as the vehicle speed increases.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NC) - TRANSMISSION CONTROL ECU ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NC) - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the transmission revolution sensor (NC) connector.


b.

Disconnect the transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B139-2 (NCB) - B133-1 (NCB) Always Below 1 Ω
B139-1 (NCO) - B133-2 (NCO) Always Below 1 Ω
B139-2 (NCB) - Body ground Always 10 kΩ or higher
B139-1 (NCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR