Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0219  Engine Overspeed Condition  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0219 Engine Overspeed Condition Diagnosis Condition:

While the engine is in operation


Malfunction Status:

An engine speed of more than 4000 rpm


Malfunction Duration:

-


·

Manual transmission (Miss-shift)

·

Operated with excessive engine oil running around to the air intake system

·

Crankshaft position sensor

·

Harness or connector

·

ECM


- DTC stored

MONITOR DESCRIPTION

The ECM detects the engine speed using the crankshaft position sensor mounted on the flywheel housing.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0219 -


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION ).


HINT:
·

In a manual transmission vehicle, a shift operation performed by the customer may over-rev the engine. If the customer indicates that over-revving has occurred, ask the customer how the vehicle was operated and offer advice.

·

When the engine oil surface rises, the engine could suck up engine oil and over-rev. If the customer indicates that over-revving has occurred, ask the customer how the vehicle was operated and offer advice.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE OIL LEVEL
a.

Check the oil level gauge and make sure the engine oil quantity is within the standard value.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (CRANKSHAFT POSITION SENSOR CONNECTOR)

NG

15.ADJUST ENGINE OIL LEVEL
2.CHECK CONNECTOR CONNECTION CONDITION (CRANKSHAFT POSITION SENSOR CONNECTOR)
a.

Check the connector connection for the crankshaft position sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CRANKSHAFT POSITION SENSOR

NG

14.CONNECT SECURELY
3.CHECK CRANKSHAFT POSITION SENSOR
a.

Check the installation of the crankshaft position sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the crankshaft position sensor.


Result:
Proceed to
OK
NG



OK

4.CHECK CRANKSHAFT POSITION SENSOR

NG

13.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
4.CHECK CRANKSHAFT POSITION SENSOR
A449991C02
0.635,0.938 1.052,1.219 0.417,0.281 2.344,1.719 1.99,1.25 true 1.229,1.688 1.646,1.271 true 0.156,0.167 0.469,0.365 0.313,0.198 10 false *a 0.76,0.99 1.073,1.188 0.313,0.198 10 false B5 2.333,1.729 2.646,1.927 0.313,0.198 10 false NE- 0.969,1.688 1.281,1.885 0.313,0.198 10 false NE+
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B5-2 (NE-) - B5-1 (NE+) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.CHECK CRANKSHAFT POSITION SENSOR

NG

5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A449991C02
0.635,0.938 1.052,1.219 0.417,0.281 2.344,1.719 1.99,1.25 true 1.229,1.688 1.646,1.271 true 0.156,0.167 0.469,0.365 0.313,0.198 10 false *a 0.76,0.99 1.073,1.188 0.313,0.198 10 false B5 2.333,1.729 2.646,1.927 0.313,0.198 10 false NE- 0.969,1.688 1.281,1.885 0.313,0.198 10 false NE+
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


a.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


b.

Disconnect the crankshaft position sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
E-52 - B5-2 (NE-) Always Below 1 Ω
E-72 - B5-1 (NE+) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


b.

Disconnect the crankshaft position sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Standard Resistance Condition Specified Condition
E-52 - Body ground and other terminals Always 10 kΩ or higher
E-72 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK CRANKSHAFT POSITION SENSOR

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK CRANKSHAFT POSITION SENSOR
A407888E01
2.75,0.104 3.427,0.292 0.677,0.188 10 false 5 V/DIV. 3.063,1.021 3.427,1.229 0.365,0.208 10 false GND 1.438,1.917 2.323,2.156 0.885,0.24 10 false 20 ms/DIV.

a.

Connect the crankshaft position sensor connector.


b.

Connect the signal check harness to the ECM.


c.

Start the engine.


d.

Use the oscilloscope to measure the voltage between the terminals of the ECM (signal check harness).

Standard Voltage:
Tester Connection Condition Specified Condition
E-52 - E-72 Idling 56 pulses for each revolution



A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Result:
Proceed to
OK
NG



OK

8.CHECK DTC OUTPUT

NG

10.REPLACE CRANKSHAFT POSITION SENSOR
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0219 is output A
DTCs are not output B




A

9.REPLACE ECM

B

END

9.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
10.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
13.REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR
a.

Repair or replace the crankshaft position sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the crankshaft position sensor.



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
14.CONNECT SECURELY
a.

Connect securely the crankshaft position sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
15.ADJUST ENGINE OIL LEVEL
a.

Adjust the engine oil quantity according to the standard value.


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END