| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P041C | EGR Temperature Sensor "B" Circuit Low | Diagnosis Condition:
·
Ignition switch ON ·
The condition that fuel injection quantity is 40 mm3/sec or less remains for 10 seconds or more. ·
The battery voltage is in the range of 10 to 16 V. ·
The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more. Malfunction Status: Output of the sensor remains at 0.04 V or less (1000°C (1832°F) or higher) for 3 seconds or longer. Malfunction Duration: 3 seconds or more |
·
Exhaust gas temperature sensor (for EGR cooler side) ·
Harness or connector ·
ECM |
Class B2 | DTC stored |
| P041D | EGR Temperature Sensor "B" Circuit High | Diagnosis Condition:
·
Ignition switch ON ·
The battery voltage is in the range of 10 to 16 V. ·
The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more. ·
Intake air temperature is -20°C (-4°F) or more. Malfunction Status: Output of the sensor remains at 4.97 V or higher (-40°C (-40°F) or lower) for 3 seconds or longer. Malfunction Duration: 3 seconds or more |
·
Exhaust gas temperature sensor (for EGR cooler side) ·
Harness or connector ·
ECM |
Class B2 | DTC stored |
The exhaust gas temperature sensor (for EGR cooler side) consistently measures temperature at the outlet of the EGR cooler.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P041C
P041D |
Idling for 3 seconds or more. |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the connector connection for the exhaust gas temperature sensor (for EGR cooler side) connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation of the exhaust gas temperature sensor (for EGR cooler side).
Make sure there is no dirt, damage or clogging in the sensing unit of the .
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the exhaust gas temperature sensor (for EGR cooler side).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (for EGR Cooler Side)) |
Disconnect the exhaust gas temperature sensor (for EGR cooler side) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B147-1 (THG) - B147-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC P041C or P041D is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Signal Check Harness Lead Connector |
| *a | Signal Check Harness Lead Connector |
Disconnect the ECM connector.
Disconnect the exhaust gas temperature sensor (for EGR cooler side) connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M-30 - Body ground and other terminals | Always | 10 kΩ or higher |
| M-54 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Exhaust Gas Temperature Sensor (for EGR Cooler Side)) |
| *a | Signal Check Harness Lead Connector |
| *a | Signal Check Harness Lead Connector |
Disconnect the ECM connector.
Disconnect the exhaust gas temperature sensor (for EGR cooler side) connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M-54 - B147-1 (THG) | Always | Below 1 Ω |
| M-30 - B147-2 (E2) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the exhaust gas temperature sensor (for EGR cooler side).
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the exhaust gas temperature sensor (for EGR cooler side).
Clean the sensing unit and install it properly.
If damaged, replace the exhaust gas temperature sensor (for EGR cooler side).
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the exhaust gas temperature sensor (for EGR cooler side).
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT