Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0524  Engine Oil Pressure Too Low  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0524 Engine Oil Pressure Too Low Diagnosis Condition:

While the engine is in operation - Always.


Malfunction Status:

The engine oil pressure switch continues to be ON for more than 30 seconds.


Malfunction Duration:

30 seconds or more


·

Oil pressure circuit

·

Engine oil pressure switch assembly

·

Harness or connector

·

ECM


- DTC stored

HINT:

When the engine oil pressure drops, notification is provided by a light in the combination meter assembly. However, if the vehicle is driven while the light is illuminated, the engine could be damaged.

Checking whether P0524 is output can help to determine whether the engine was damaged due to a drop in engine oil pressure.


MONITOR DESCRIPTION

A drop in engine oil pressure is sensed by the engine oil pressure switch assembly.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0524 After warming up engine, idle engine for 30 seconds or more.


WIRING DIAGRAM

A452525E01
1.115,1.938 4.323,2.135 3.208,0.198 10 false Engine Oil Pressure Switch Assembly 1.135,1.75 1.448,1.948 0.313,0.198 10 false B9 2.656,1.24 2.969,1.438 0.313,0.198 10 false 1 4.927,1.354 5.354,1.552 0.427,0.198 10 false OIL 4.667,1.219 5.094,1.417 0.427,0.198 10 false 15 4.906,2.219 6.833,2.417 1.927,0.198 10 false Combination Meter 1.385,1.24 1.698,1.438 0.313,0.198 10 false 2 4.896,2.031 5.323,2.229 0.427,0.198 10 false J1

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:
·

An output DTC does not necessarily indicate that there is a malfunction. DTCs may have been stored due to an insufficient engine oil amount even though the oil level warning light is currently not illuminated, such as when engine oil is added by the customer.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ENGINE OIL LEVEL
a.

Check the engine oil condition (dirt, viscosity).

Click hereEngine / Hybrid System>N04C-WA (LUBRICATION)>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION


b.

Check the oil level gauge and make sure the engine oil quantity is within the stipulated value.


Result:
Proceed to
OK
NG



OK

2.CHECK ENGINE OIL LEAKS

NG

13.ADJUST ENGINE OIL QUANTITY
2.CHECK ENGINE OIL LEAKS
a.

Make sure there is no oil leaking from the engine unit or from around the oil pressure switch.


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION (ENGINE OIL PRESSURE SWITCH ASSEMBLY CONNECTOR)

NG

12.REPAIR FAULTY PART
3.CHECK CONNECTOR CONNECTION CONDITION (ENGINE OIL PRESSURE SWITCH ASSEMBLY CONNECTOR)
a.

Check the connector connection for the engine oil pressure switch assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.INSPECT ENGINE OIL PRESSURE SWITCH ASSEMBLY

NG

11.CONNECTOR SECURELY
4.INSPECT ENGINE OIL PRESSURE SWITCH ASSEMBLY
a.

Inspect the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>N04C-WA (LUBRICATION)>OIL PRESSURE SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

10.REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


b.
A452676C01
0.396,0.885 0.823,1.135 0.427,0.25 0.521,0.927 0.833,1.125 0.313,0.198 10 false B9 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Engine Oil Pressure Switch Assembly)


A241244C09
1.5,0.333 1.833,0.583 0.333,0.25 2.583,1.792 2.302,1.229 true 0.094,0.083 0.333,0.271 0.24,0.188 10 false *a 2.552,1.844 3.167,2.042 0.615,0.198 10 false OIL 1.583,0.385 1.813,0.552 0.229,0.167 10 false J1
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the engine oil pressure switch assembly connector.


c.

Disconnect the combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-1 - Body ground and other terminals Always 10 kΩ or higher
J1-15 (OIL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS AND CONNECTOR (ENGINE OIL PRESSURE SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


b.
A452676C01
0.396,0.885 0.823,1.135 0.427,0.25 0.521,0.927 0.833,1.125 0.313,0.198 10 false B9 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Engine Oil Pressure Switch Assembly)


A241244C09
1.5,0.333 1.833,0.583 0.333,0.25 2.583,1.792 2.302,1.229 true 0.094,0.083 0.333,0.271 0.24,0.188 10 false *a 2.552,1.844 3.167,2.042 0.615,0.198 10 false OIL 1.583,0.385 1.813,0.552 0.229,0.167 10 false J1
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B9-1 - J1-15 (OIL) Always Below 1 Ω
B9-2 - Body ground and other terminals Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.REPLACE ECM

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.REPLACE ENGINE OIL PRESSURE SWITCH ASSEMBLY
a.

Replace the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>N04C-WA (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
11.CONNECTOR SECURELY
a.

Connect securely the engine oil pressure switch assembly.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPAIR FAULTY PART
a.

Repair the faulty part.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.ADJUST ENGINE OIL QUANTITY
a.

Adjust the engine oil quantity so that it is within the stipulated value.

HINT:

Change the oil if it is dirty.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END