Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0850  Park/Neutral Switch Input Circuit  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0850 Park/Neutral Switch Input Circuit Diagnosis Condition:
·

After the ignition switch ON position, the status described below remains for 10 seconds.

-

MT vehicle is driven at speeds over 80 km/h (50 mile), then slowed down to a stop.



Malfunction Status:
·

Detected at one of the following conditions.

-

The signal that the exhaust brake neutral switch assembly never turned on and off is detected twice in succession.



Malfunction Duration:

-


·

Exhaust brake neutral switch assembly

·

Harness or connector

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

Neutral signal is sensed by the ECM through the exhaust brake neutral switch assembly when the gear is in neutral.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0850 Repeatedly accelerate and decelerate from 0 to 80 km/h


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY CONNECTOR)
a.

Check the connector connection for the exhaust brake neutral switch assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY

NG

7.CONNECT SECURELY
2.INSPECT EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY
a.

Inspect the exhaust brake neutral switch assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - BODY GROUND)

NG

6.REPLACE EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY - BODY GROUND)
A405886C10
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V-11 - Body ground Ignition switch ON
Shift position is neutral
11 V or higher
V-11 - Body ground Ignition switch ON
Shift position is not neutral
Below 1 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
6.REPLACE EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY
a.

Replace the exhaust brake neutral switch assembly.


Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
7.CONNECT SECURELY
a.

Connect securely the exhaust brake neutral switch assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

8.CHECK DTC OUTPUT
8.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END