Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P04D5  Exhaust Brake Input Circuit Low  P04D6  Exhaust Brake Input Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P04D5 Exhaust Brake Input Circuit Low Diagnosis Condition:
·

Exhaust brake inactivity request is in progress.

·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

The condition that the exhaust brake solenoid assembly circuit voltage is 3.0 V or less remains for 3 seconds or more.


Malfunction Duration:

3 seconds or more


·

Exhaust brake solenoid with bracket assembly

·

Harness or connector

·

ECM


Class C DTC stored
P04D6 Exhaust Brake Input Circuit High Diagnosis Condition:
·

Exhaust brake activity request is in progress.

·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

The condition that the exhaust brake solenoid assembly circuit current is 4.5 A or higher is remains for 3 seconds or more.


Malfunction Duration:

3 seconds or more


·

Exhaust brake solenoid with bracket assembly

·

Harness or connector

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

P04D5:
·

Exhaust brake solenoid assembly is not working properly.

·

Possible exhaust brake solenoid assembly failure or GND short-circuit


P04D6:
·

Exhaust brake solenoid assembly is not working properly.

·

Possible exhaust brake solenoid assembly failure or +B short-circuit or disconnection


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P04D5 Ignition switch ON for 8 seconds or more.
P04D6 Exhaust brake ON for 8 seconds or more


WIRING DIAGRAM

A452524E01
6.042,5.521 6.5,5.719 0.458,0.198 10 false EXB 6.042,5.01 6.5,5.208 0.458,0.198 10 false EXB 6.052,2.552 6.792,2.74 0.74,0.188 10 false NUSW 6.063,1.469 6.521,1.667 0.458,0.198 10 false EXSW 6.063,0.365 6.656,0.625 0.594,0.26 10 false CLSW 6.042,4.458 6.5,4.656 0.458,0.198 10 false MREL 6.052,4.021 6.51,4.219 0.458,0.198 10 false MREL 6.042,6.104 6.5,6.302 0.458,0.198 10 false E01 5.625,0.344 6.083,0.542 0.458,0.198 10 false A115 5.615,1.469 6.073,1.667 0.458,0.198 10 false A115 5.615,2.531 6.073,2.729 0.458,0.198 10 false A115 5.625,4.031 6.083,4.229 0.458,0.198 10 false A115 5.625,4.469 6.083,4.667 0.458,0.198 10 false A115 5.615,5.01 6.073,5.208 0.458,0.198 10 false A115 5.625,5.51 6.083,5.708 0.458,0.198 10 false A115 5.625,6.104 6.083,6.302 0.458,0.198 10 false A115 5.708,5.906 6.167,6.104 0.458,0.198 10 false 12 5.708,4.26 6.167,4.458 0.458,0.198 10 false 26 5.729,3.802 6.188,4 0.458,0.198 10 false 27 5.698,5.302 6.156,5.5 0.458,0.198 10 false 40 5.719,4.771 6.177,4.969 0.458,0.198 10 false 41 5.719,0.177 6.177,0.375 0.458,0.198 10 false 17 5.708,1.281 6.167,1.479 0.458,0.198 10 false 68 5.688,2.333 6.146,2.531 0.458,0.198 10 false 31 6.292,6.573 6.76,6.865 0.469,0.292 10 false ECM 5.25,0.365 5.708,0.563 0.458,0.198 10 false V-55 5.25,1.469 5.708,1.667 0.458,0.198 10 false V-54 5.24,2.542 5.698,2.74 0.458,0.198 10 false V-11 5.302,5.5 5.76,5.698 0.458,0.198 10 false V-4 5.302,5 5.76,5.198 0.458,0.198 10 false E-3 5.26,4.458 5.719,4.656 0.458,0.198 10 false V-23 5.302,4.021 5.76,4.219 0.458,0.198 10 false V-3 5.25,6.104 5.708,6.302 0.458,0.198 10 false V-40 2.292,2.958 5.51,3.531 3.219,0.573 10 false Exhaust Brake Neutral Switch Assembly*2 2.292,2.802 2.75,3 0.458,0.198 11 false B25 3.406,0.813 4.948,1.198 1.542,0.385 10 false Exhaust Brake Switch 3.406,0.635 3.865,0.833 0.458,0.198 10 false H3 3.635,1.958 4.625,2.271 0.99,0.313 10 false Wiper Switch 1.885,1 2.865,1.219 0.979,0.219 10 false ECU-IG1 NO.4 3.646,1.792 4.104,1.99 0.458,0.198 10 false J65 0.25,0.833 1.979,1.219 1.729,0.385 10 false From IG1-NO.1 Relay 4.844,2.417 5.302,2.615 0.458,0.198 10 false 1 3.156,2.417 3.615,2.615 0.458,0.198 10 false 2 1.927,4.906 2.385,5.104 0.458,0.198 10 false 5 3.271,4.875 3.729,5.073 0.458,0.198 10 false 1 4.542,0.229 5,0.427 0.458,0.198 10 false 2 3.469,0.24 3.927,0.438 0.458,0.198 10 false 1 4.563,1.354 5.021,1.552 0.458,0.198 10 false 9 3.469,1.365 3.927,1.563 0.458,0.198 10 false 8 4.344,1.323 4.802,1.521 0.458,0.198 10 false L 3.708,1.323 4.167,1.521 0.458,0.198 10 false B 2.594,5.156 3.24,5.365 0.646,0.208 10 false EFI NO.2 1.229,5.375 1.979,5.583 0.75,0.208 10 false ACT PWR 0.365,5.427 1.115,5.635 0.75,0.208 10 false EFI-MAIN 0.427,4.625 1.073,4.833 0.646,0.208 10 false EFI NO.1 0.385,5.896 1.135,6.104 0.75,0.208 10 false P/I 0.354,6.323 1.198,6.552 0.844,0.229 10 false R/B NO.2-B 0.479,7.26 1.323,7.49 0.844,0.229 10 false Battery 0.365,6.781 1.208,7.01 0.844,0.229 10 false FL-MAIN 3.323,5.531 4.833,5.885 1.51,0.354 10 false Exhaust Brake Solenoid Assembly 3.333,5.354 3.792,5.552 0.458,0.198 10 false A4 3.271,3.927 5.135,4.292 1.865,0.365 10 false Neutral Switch Assembly*1 3.271,3.771 3.729,3.969 0.458,0.198 10 false B21 3.073,6.365 3.823,6.573 0.75,0.208 10 false *1: A/T 3.344,2.542 3.802,2.74 0.458,0.198 10 false NSW- 4.354,2.552 4.813,2.75 0.458,0.198 10 false NSW+ 3.073,6.521 3.823,6.729 0.75,0.208 10 false *2: M/T 4.729,4.854 5.188,5.052 0.458,0.198 10 false 2 1.135,4.354 1.594,4.552 0.458,0.198 10 false 1 1.125,4.906 1.583,5.104 0.458,0.198 10 false 3 1.927,4.354 2.385,4.552 0.458,0.198 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK EXHAUST BRAKE SOLENOID ASSEMBLY CONNECTOR
a.

Check the connection of the exhaust brake solenoid assembly connector (looseness and poor contact).


Result:
Proceed to
OK
NG



OK

2.CHECK EXHAUST BRAKE SOLENOID ASSEMBLY

NG

14.CONNECT SECURELY
2.CHECK EXHAUST BRAKE SOLENOID ASSEMBLY
a.

Check the installation of the exhaust brake solenoid assembly.


Result:
Proceed to
OK
NG



OK

3.INSPECT EXHAUST BRAKE SOLENOID ASSEMBLY

NG

13.REPLACE EXHAUST BRAKE SOLENOID WITH BRACKET ASSEMBLY
3.INSPECT EXHAUST BRAKE SOLENOID ASSEMBLY
a.

Inspect the exhaust brake solenoid assembly .

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER SOLENOID>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK EXHAUST BRAKE SOLENOID ASSEMBLY

NG

12.REPLACE EXHAUST BRAKE SOLENOID WITH BRACKET ASSEMBLY
4.CHECK EXHAUST BRAKE SOLENOID ASSEMBLY
A451737C02
0.448,1.031 0.844,1.302 0.396,0.271 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.573,1.104 0.885,1.302 0.313,0.198 10 false A4
*a Front view of wire harness connector
(to Exhaust Brake Solenoid Assembly Connector)


a.

Disconnect the exhaust brake solenoid assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A4-1 - Body ground Ignition switch ON 11 V or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS OR CONNECTOR (EXHAUST BRAKE SOLENOID ASSEMBLY - ECU)

NG

11.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS OR CONNECTOR (EXHAUST BRAKE SOLENOID ASSEMBLY - ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the exhaust brake solenoid assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C11
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-3 - V-40 Ignition switch off 10 kΩ or higher
V-4 - V-40 Ignition switch off 10 kΩ or higher



Result:
Proceed to
OK
NG


A405886C08
1.49,0.094 1.896,0.375 0.406,0.281 0.281,0.167 0.594,0.365 0.313,0.198 10 false *a 1.625,0.156 1.938,0.354 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector



OK

6.CHECK HARNESS OR CONNECTOR (EXHAUST BRAKE SOLENOID ASSEMBLY - ECU)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS OR CONNECTOR (EXHAUST BRAKE SOLENOID ASSEMBLY - ECU)
a.

Disconnect the ECM connector.


b.

Disconnect the exhaust brake solenoid assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405886C11
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E-3 - V-40 Ignition switch ON 11 V or higher
V-4 - V-40 Ignition switch ON 11 V or higher



Result:
Proceed to
OK
NG


A405886C08
1.49,0.094 1.896,0.375 0.406,0.281 0.281,0.167 0.594,0.365 0.313,0.198 10 false *a 1.625,0.156 1.938,0.354 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector



OK

7.CHECK DTC OUTPUT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK DTC OUTPUT
a.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


b.

Stop the engine.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



f.

Turn the ignition switch off for 30 seconds or more.


g.

Perform the confirmation driving pattern.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read Current DTCs.

Result:
Result Proceed to
DTC P04D5 or P04D6 is output A
DTCs are not output B




A

8.REPLACE ECM

B

15.CHECK DTC OUTPUT
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
11.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
12.REPLACE EXHAUST BRAKE SOLENOID WITH BRACKET ASSEMBLY
a.

Replace the exhaust brake solenoid with bracket assembly.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
13.REPLACE EXHAUST BRAKE SOLENOID WITH BRACKET ASSEMBLY
a.

Install the exhaust brake solenoid assembly correctly.


b.

Replace the exhaust brake solenoid assembly if it is damaged.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
14.CONNECT SECURELY
a.

Connect securely the exhaust brake solenoid assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
15.CHECK DTC OUTPUT
a.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


b.

Stop the engine.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



f.

Turn the ignition switch off for 30 seconds or more.


g.

Perform the confirmation driving pattern.


h.

Turn the GTS on.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END