Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM J

N04C-WA ENGINE CONTROL  ECD SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the No. 2 integration relay (EFI), closing the contacts and supplying power to terminals +B of the ECM.

WIRING DIAGRAM

A449937E01
6.188,0.49 6.5,0.688 0.313,0.198 10 false IG 6.188,0.906 6.635,1.125 0.448,0.219 10 false IGSW 5.75,0.458 6.177,0.688 0.427,0.229 10 false A115 5.75,0.885 6.177,1.115 0.427,0.229 10 false A115 5.865,0.271 6.292,0.5 0.427,0.229 10 false 5 5.865,0.698 6.292,0.927 0.427,0.229 10 false 6 5.385,0.875 5.813,1.104 0.427,0.229 10 false V-13 5.385,0.448 5.813,0.677 0.427,0.229 10 false V-33 4.5,1.052 5.125,1.25 0.625,0.198 10 false IGN NO.1 0.583,1.813 1.781,2.073 1.198,0.26 10 false Ignition Switch 0.583,1.677 1.208,1.875 0.625,0.198 10 false J63 0.604,1.26 1.229,1.458 0.625,0.198 10 false AM1 0.292,2.563 0.917,2.76 0.625,0.198 10 false AM1 0.302,3.229 0.927,3.427 0.625,0.198 10 false J/B-ALT 0.313,3.854 0.938,4.052 0.625,0.198 10 false ALT 0.323,4.698 0.948,4.896 0.625,0.198 10 false FL-MAIN 0.427,5.219 1.052,5.417 0.625,0.198 10 false Battery 1.25,1.26 1.875,1.458 0.625,0.198 10 false IG1 3.24,1.615 3.865,1.813 0.625,0.198 10 false IG2 2.427,1.042 3.052,1.24 0.625,0.198 10 false IG2 NO.1 0.438,1.219 0.719,1.438 0.281,0.219 10 false 6 1.542,1.219 1.823,1.438 0.281,0.219 10 false 5 6.167,1.375 6.615,1.594 0.448,0.219 10 false +B1 6.156,1.75 6.604,1.969 0.448,0.219 10 false +B2 6.156,2.333 6.604,2.552 0.448,0.219 10 false +B3 5.813,1.167 6.26,1.385 0.448,0.219 10 false 13 5.823,1.552 6.271,1.771 0.448,0.219 10 false 37 5.833,2.115 6.281,2.333 0.448,0.219 10 false 61 5.74,1.354 6.167,1.583 0.427,0.229 10 false A115 5.74,1.729 6.167,1.958 0.427,0.229 10 false A115 5.75,2.313 6.177,2.542 0.427,0.229 10 false A115 4.01,2.302 4.438,2.531 0.427,0.229 10 false 2C 4.042,2.104 4.49,2.323 0.448,0.219 10 false 4 3.219,3 3.646,3.229 0.427,0.229 10 false EDU 4,2.74 4.427,2.969 0.427,0.229 10 false 2C 4.042,2.542 4.469,2.771 0.427,0.229 10 false 3 1.875,2.729 2.302,2.958 0.427,0.229 10 false 2C 1.948,2.542 2.375,2.771 0.427,0.229 10 false 2 2.563,2.479 2.99,2.708 0.427,0.229 10 false EDU 5.75,2.74 6.177,2.969 0.427,0.229 10 false A115 5.74,3.156 6.167,3.385 0.427,0.229 10 false A115 6.167,3.167 6.615,3.385 0.448,0.219 10 false MREL 6.156,2.771 6.604,2.99 0.448,0.219 10 false MREL 5.823,2.563 6.271,2.781 0.448,0.219 10 false 26 5.823,2.969 6.271,3.188 0.448,0.219 10 false 27 4.594,3.906 5.021,4.135 0.427,0.229 10 false 2 3.833,3.906 4.26,4.135 0.427,0.229 10 false 1 6.177,4.625 6.625,4.844 0.448,0.219 10 false BATT 3.177,4.167 4,4.375 0.823,0.208 10 false EFI NO.1 3.948,4.281 4.771,4.49 0.823,0.208 10 false ACT PWR 5.74,4.594 6.167,4.823 0.427,0.229 10 false A115 5.823,4.406 6.25,4.635 0.427,0.229 10 false 70 2.396,3.396 3.219,3.604 0.823,0.208 10 false EFI-MAIN 3.823,3.479 4.25,3.708 0.427,0.229 10 false 3 4.594,3.479 5.021,3.708 0.427,0.229 10 false 5 4.781,3.729 5.604,3.938 0.823,0.208 10 false EFI NO.2 5.74,3.573 6.167,3.802 0.427,0.229 10 false A115 5.823,3.385 6.25,3.615 0.427,0.229 10 false 49 6.167,3.594 6.615,3.813 0.448,0.219 10 false +B 6.167,5.219 6.615,5.438 0.448,0.219 10 false E01 6.156,5.625 6.604,5.844 0.448,0.219 10 false E02 6.177,6.021 6.625,6.24 0.448,0.219 10 false E11 5.75,5.188 6.177,5.417 0.427,0.229 10 false A115 5.75,5.594 6.177,5.823 0.427,0.229 10 false A115 5.74,5.99 6.167,6.219 0.427,0.229 10 false A115 5.385,5.177 5.833,5.396 0.448,0.219 10 false V-40 5.385,5.583 5.833,5.802 0.448,0.219 10 false V-60 5.375,5.979 5.823,6.198 0.448,0.219 10 false V-39 5.823,5.813 6.271,6.031 0.448,0.219 10 false 60 5.833,5.417 6.281,5.635 0.448,0.219 10 false 36 5.823,5 6.271,5.219 0.448,0.219 10 false 12 5.396,4.583 5.844,4.802 0.448,0.219 10 false V-19 5.427,3.573 5.875,3.792 0.448,0.219 10 false V-1 5.417,3.146 5.865,3.365 0.448,0.219 10 false V-3 5.385,1.344 5.813,1.573 0.427,0.229 10 false V-18 5.375,1.719 5.802,1.948 0.427,0.229 10 false V-38 5.396,2.302 5.823,2.531 0.427,0.229 10 false V-58 5.396,2.729 5.844,2.948 0.448,0.219 10 false V-23 6.396,6.469 6.938,6.698 0.542,0.229 10 false ECM 1.885,2.302 2.313,2.531 0.427,0.229 10 false 2E 1.938,2.094 2.365,2.323 0.427,0.229 10 false 1 1.333,2.5 1.76,2.729 0.427,0.229 10 false P/I 1.125,3.792 1.708,4.313 0.583,0.521 10 false R/B NO.2-B 1.885,1.323 2.313,1.552 0.427,0.229 10 false 2C 1.938,1.125 2.219,1.344 0.281,0.219 10 false 6 4.01,0.885 4.438,1.115 0.427,0.229 10 false 2C 4,1.344 4.427,1.573 0.427,0.229 10 false 2C 4.042,0.698 4.323,0.917 0.281,0.219 10 false 8 4.042,1.135 4.323,1.354 0.281,0.219 10 false 7 1.219,2.896 1.688,3.5 0.469,0.604 10 false ECU-B NO.1 2.74,4.01 3.167,4.24 0.427,0.229 10 false 2D 2.771,3.823 3.198,4.052 0.427,0.229 10 false 1 1.688,4.406 3.427,4.646 1.74,0.24 10 false No. 2 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT ECM (+B VOLTAGE)
a.
A405886C13
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Turn the ignition switch off.


b.

Connect the signal check harness to the ECM vehicle side harness.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-1 - V-40 Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT ECM (+B1,+B2, +B3 VOLTAGE)

NG

13.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
2.INSPECT ECM (+B1,+B2, +B3 VOLTAGE)
a.
A405886C14
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


A405887C21
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false V
*a Signal Check Harness Lead Connector


Turn the ignition switch off.


b.

Connect the signal check harness to the ECM vehicle side harness.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-18 - V-40 Ignition switch ON 11 to 14 V
V-38 - V-40 Ignition switch ON 11 to 14 V
V-58 - V-40 Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


A405887C21
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-40 - Body ground Always Below 1 Ω
V-60 - Body ground Always Below 1 Ω
V-39 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT ECM (IGSW VOLTAGE)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-13 - V-40 Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (MREL VOLTAGE)

NG

9.INSPECT NO.2 INTEGRATION RELAY (IG2 RELAY)
5.INSPECT ECM (MREL VOLTAGE)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V-23 - V-40 Ignition switch off 11 to 14 V
V-3 - V-40 Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT ECM (MREL VOLTAGE)

NG

7.INSPECT NO.2 INTEGRATION RELAY (EDU RELAY)
6.INSPECT ECM (MREL VOLTAGE)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V-23 - V-40 Ignition switch ON 0 to 2 V
V-3 - V-40 Ignition switch ON 0 to 2 V



Result:
Proceed to
OK
NG



OK

7.INSPECT NO.2 INTEGRATION RELAY (EDU RELAY)

NG

7.INSPECT NO.2 INTEGRATION RELAY (EDU RELAY)
a.

Inspect the No. 2 integration relay (EDU relay) (Click here Engine / Hybrid System>N04C-UH (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (ECM - NO. 2 INTEGRATION RELAY)

NG

REPLACE NO.2 INTEGRATION RELAY

8.CHECK HARNESS AND CONNECTOR (ECM - NO. 2 INTEGRATION RELAY)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


A405887C06
1.521,0.125 1.885,0.396 0.365,0.271 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a 1.677,0.198 1.833,0.396 0.156,0.198 10 false V
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-23 - 2C-3 Always Below 1 Ω
V-18 - 2C-4 Always Below 1 Ω
V-38 - 2C-4 Always Below 1 Ω
V-58 - 2C-4 Always Below 1 Ω
V-23 or 2C-3 - Body ground Always 10 kΩ or higher
V-18 or 2C-4 - Body ground Always 10 kΩ or higher
V-38 or 2C-4 - Body ground Always 10 kΩ or higher
V-58 or 2C-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (EDU RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT NO.2 INTEGRATION RELAY (IG2 RELAY)
a.

Inspect the No. 2 integration relay (IG2 relay)

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (ECM - NO.2 INTEGRATION RELAY)

NG

REPLACE NO.2 INTEGRATION RELAY

10.CHECK HARNESS AND CONNECTOR (ECM - NO.2 INTEGRATION RELAY)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-13 - 2C-8 Always Below 1 Ω
V-13 or 2C-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION SWITCH ASSEMBLY

Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - NO. 2 INTEGRATION RELAY)

NG

REPLACE IGNITION SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Disconnect the ignition switch connector.


b.

Remove the No. 2 integration relay from the No. 2 relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J63-5 (IG1) - 2C-6 Always Below 1 Ω
2C-7 - Body ground Always Below 1 Ω
J63-5 (IG1) or 2C-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


A405887C21
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-40 - Body ground Always Below 1 Ω
V-60 - Body ground Always Below 1 Ω
V-39 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

14.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT ECM (IGSW VOLTAGE)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-13 - V-40 Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.INSPECT ECM (MREL VOLTAGE)

NG

9.INSPECT NO.2 INTEGRATION RELAY (IG2 RELAY)
15.INSPECT ECM (MREL VOLTAGE)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V-23 - V-40 Ignition switch off 11 to 14 V
V-3 - V-40 Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

16.INSPECT ECM (MREL VOLTAGE)

NG

17.INSPECT ACT PWR RELAY
16.INSPECT ECM (MREL VOLTAGE)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Connect the signal check harness to the ECM vehicle side harness.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
V-23 - V-40 Ignition switch ON 0 to 2 V
V-3 - V-40 Ignition switch ON 0 to 2 V



Result:
Proceed to
OK
NG



OK

17.INSPECT ACT PWR RELAY

NG

17.INSPECT ACT PWR RELAY

Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (ECM - ACT PWR RELAY)

NG

REPLACE ACT PWR RELAY

18.CHECK HARNESS AND CONNECTOR (ECM - ACT PWR RELAY)
a.
A405886C15
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Disconnect the ACT PWR relay to the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-1 - ACT PWR relay terminal 5 Always Below 1 Ω
V-3 - ACT PWR relay terminal 2 Always Below 1 Ω
V-1 or ACT PWR relay terminal 5 - Body ground Always 10 kΩ or higher
V-3 or ACT PWR relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (ACT PWR RELAY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR