| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2032 | Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 2 | Diagnosis Condition:
·
Battery voltage is in the range of 10 V to 16 V ·
Engine is running at engine speed over 490 rpm for at least 5 seconds. Malfunction Status: Voltage of the No. 2 exhaust gas temperature sensor remains less than 0.057 V for 3 seconds. Malfunction Duration: 3 seconds or more |
·
No. 2 exhaust gas temperature sensor ·
Harness or connector ·
ECM |
Class B1 | DTC stored |
| P2033 | Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 2 | Diagnosis Condition:
·
Battery voltage is in the range of 10 V to 16 V ·
Engine is running at engine speed over 490 rpm for at least 5 seconds. Malfunction Status: Voltage of the No. 2 exhaust gas temperature sensor remains at 4.958 V for 60 seconds. Malfunction Duration: 60 seconds or more |
·
No. 2 exhaust gas temperature sensor ·
Harness or connector ·
ECM |
Class B1 | DTC stored |
The No. 2 exhaust gas temperature sensor consistently detects exhaust gas temperature.
A reading taken by the No. 2 exhaust gas temperature sensor is used to control DPR regeneration.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2032 | Idle the engine for 3 seconds or more. |
| P2033 | Idle the engine for 60 seconds or more. |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the connector connection for the No. 2 exhaust gas temperature sensor connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation of the No. 2 exhaust gas temperature sensor.
Make sure there is no dirt, damage or clogging in the sensing unit of the No. 2 exhaust gas temperature sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 2 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor) |
Disconnect the No. 2 exhaust gas temperature sensor.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch | Specified Condition |
|---|---|---|
| A110-1 (THCO) - A110-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the No. 2 exhaust gas temperature sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V-46 - Body ground and other terminals | Always | 10 kΩ or higher |
| V-49 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the No. 2 exhaust gas temperature sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V-46 - V-49 | Always (20 °C) | 13.7 to 29.8 kΩ |
| V-46 - V-49 | Always (50 °C) | 7.13 to 13.7 kΩ |
| V-46 - V-49 | Always (80 °C) | 4.1 to 7.13 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC P2032 or P2033 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the exhaust gas temperature sensor No. 2.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 2 exhaust gas temperature sensor.
Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the No. 2 exhaust gas temperature sensor.
Clean the sensing unit and install it properly.
If damaged, replace No. 2 exhaust gas temperature sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the No. 2 exhaust gas temperature sensor connector.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT