Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2080  Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2080 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1 Diagnosis Condition:
Engine start-up
·

Battery voltage is in the range of 10 V to 16 V

·

Engine speed 500 rpm or more for at least 5 seconds.

·

Less than 10 seconds has elapsed since start of engine.

·

Difference between engine coolant temperature and intake temperature is within 10°C (18°F).

·

Difference between engine coolant temperature before ignition switch ON and after ignition switch ON is 20°C (68°F) or more.

·

Engine coolant temperature and intake temperature are at least -10°C (14°F).


Driving
·

At least 10 seconds has elapsed since engine was started.

·

Cumulative exhaust gas flow amount more than 2 kg.

·

Cumulative exhaust gas flow amount of 20 kg or more with after regeneration.

·

After the above

-

Battery voltage is in the range of 10 V to 16 V

-

Engine speed 500 rpm or more for at least 5 seconds.

-

Engine speed 1000 rpm or more

-

Exhaust fuel addition injector amount higher than 30 mm3/st

-

Exhaust gas flow rate higher than 120 kg/h

-

Difference between engine coolant temperature and intake temperature is more than 10°C (18°F).


·

In addition, the following conditions continue for at least 10 seconds

-

Engine speed variation is within 25 rpm.

-

Exhaust fuel addition injector rate variation is within 5 mm3/st.

-

Vehicle speed 30 km/h (19 mile) or more



Malfunction Status:
Engine start-up
·

The conditions described below remain for 1 seconds or more.

-

Difference between No. 1 exhaust gas temperature sensor and No. 2 exhaust gas temperature sensor stays more than 70°C (126°F).

-

Difference between No. 2 exhaust gas temperature sensor and No. 3 exhaust gas temperature sensor stays less than 70°C (126°F).

-

Difference between No. 3 exhaust gas temperature sensor and No. 4 exhaust gas temperature sensor stays less than 70°C (126°F).



Driving
·

Difference between calculated value and actual value of No. 1 exhaust gas temperature sensor is not less than 60°C (140°F) for 3 seconds.

·

Difference between calculated value and actual value of No. 2 exhaust gas temperature sensor is not less than 100°C (212°F) for 3 seconds.


Malfunction Duration:
Engine start-up

5 seconds or more


Driving

3 seconds or more


·

No. 1 exhaust gas temperature sensor

·

No. 2 exhaust gas temperature sensor

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

·

The exhaust gas temperature is constantly detected by the No. 1 exhaust gas temperature sensor.

·

The value of the No. 1 exhaust gas temperature sensor is used to control DPR regeneration.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2080 Drive for a certain amount of time after starting the engine.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK EXHAUST PIPE
a.

Check for exhaust pipe crack, exhaust gas leak (soot contamination) and improper coupling flange tightening.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)

NG

28.REPAIR OR REPLACE EXHAUST PIPE
2.CHECK CONNECTOR CONNECTION CONDITION (NO. 1 EXHAUST GAS TEMPERATURE SENSOR CONNECTOR)
a.

Check the connector connection for the No. 1 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

27.CONNECT SECURELY
3.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 1 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 1 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

26.REPAIR OR REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
4.INSPECT NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 1 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

25.REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
5.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR
A450001C01
0.604,0.948 1.021,1.25 0.417,0.302 2.323,1.802 1.885,1.219 true 1.25,1.781 1.563,1.229 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.656,1.031 1.167,1.208 0.51,0.177 10 false B141 2.271,1.833 2.729,2.031 0.458,0.198 10 false GND 0.969,1.833 1.427,2.031 0.458,0.198 10 false TOIL
*a Front view of wire harness connector
(to No. 1 Exhaust Gas Temperature Sensor)


a.

Disconnect the No. 1 exhaust gas temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B141-1 (TOIL) - B141-2 (GND) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (EXHAUST GAS TEMPERATURE SENSOR NO. 2)

NG

19.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)
6.CHECK CONNECTOR CONNECTION CONDITION (EXHAUST GAS TEMPERATURE SENSOR NO. 2)
a.

Check the connector connection for the exhaust gas temperature sensor No. 2 connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

7.CHECK EXHAUST GAS TEMPERATURE SENSOR NO. 2

NG

18.CONNECT SECURELY
7.CHECK EXHAUST GAS TEMPERATURE SENSOR NO. 2
a.

Check the installation of the exhaust gas temperature sensor No. 2.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the exhaust gas temperature sensor No. 2.


Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 2 EXHAUST GAS TEMPERATURE SENSOR

NG

17.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR NO. 2
8.INSPECT NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK NO. 2 EXHAUST GAS TEMPERATURE SENSOR

NG

16.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
9.CHECK NO. 2 EXHAUST GAS TEMPERATURE SENSOR
A449999C01
0.604,0.948 1.146,1.26 0.542,0.313 2.26,1.75 1.854,1.198 true 1.177,1.76 1.583,1.198 true 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 0.729,1.021 1.167,1.219 0.438,0.198 10 false A110 2.156,1.802 2.771,2 0.615,0.198 10 false THCO 1.052,1.802 1.667,2 0.615,0.198 10 false E2
*a Front view of wire harness connector
(to No. 2 Exhaust Gas Temperature Sensor)


a.

Disconnect the No. 2 exhaust gas temperature sensor.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Specified Condition
A110-1 (THCO) - A110-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

10.CHECK HARNESS OR CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
10.CHECK HARNESS OR CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the No. 2 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - Body ground and other terminals Always 10 kΩ or higher
V-49 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS OR CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.CHECK HARNESS OR CONNECTOR (NO. 2 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the No. 2 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - V-49 Always (20°C) 13.7 to 29.8 kΩ
V-46 - V-49 Always (50°C) 7.13 to 13.7 kΩ
V-46 - V-49 Always (80°C) 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

14.REPAIR OR REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2080 is output A
DTCs are not output B




A

13.REPLACE ECM

B

END

13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
14.REPAIR OR REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
16.REPLACE NO. 2 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 2 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
17.REPAIR OR REPLACE EXHAUST GAS TEMPERATURE SENSOR NO. 2
a.

Repair or replace the exhaust gas temperature sensor No. 2.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the exhaust gas temperature sensor No. 2.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
18.CONNECT SECURELY
a.

Connect securely the exhaust gas temperature sensor No. 2 connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
19.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the No. 1 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-50 - Body ground and other terminals Always 10 kΩ or higher
E-77 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the No. 1 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-50 - E-77 Always (20°C) 13.7 to 29.8 kΩ
M-50 - E-77 Always (50°C) 7.13 to 13.7 kΩ
M-50 - E-77 Always (80°C) 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

21.CHECK DTC OUTPUT

NG

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
21.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P2080 is output A
DTCs are not output B




A

22.REPLACE ECM

B

END

22.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
23.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
24.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
25.REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 1 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
26.REPAIR OR REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 1 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 1 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
27.CONNECT SECURELY
a.

Connect securely the No. 1 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
28.REPAIR OR REPLACE EXHAUST PIPE
a.

Repair the exhaust pipe.

HINT:

Replace it as needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
29.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END