| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2101 | Throttle Actuator "A" Control Motor Circuit Range/Performance | Diagnosis Condition:
The conditions described below remain for 10 seconds or more. ·
Ignition switch ON ·
Battery voltage is in the range of 10 V to 16 V ·
The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more. ·
A change in the engine speed is 20 rpm or less. ·
A change in exhaust fuel addition injector quantity is 2 mm3/st or less. Malfunction Status: A state, in which the difference obtained by (actual diesel throttle valve opening - target diesel throttle valve opening) is 10% or more or -10% or less, has continued for 30 seconds or more. Malfunction Duration: 30 seconds or more |
·
Air cleaner filter element sub-assembly ·
Intake hose ·
Exhaust muffler ·
Exhaust retarder assembly. ·
Diesel throttle body ·
ECM |
Class A | DTC stored |
The throttle valve built into the diesel throttle body is butterfly valve type, and actuated by the rotary solenoid.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P2101 | Start the engine and idle the engine for 40 seconds or more. |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the air cleaner element sub-assembly for dirt or damage, and make sure the replacement period has not expired.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the air hose and pipe have no disconnections, clogging, ruptures, or cracks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the exhaust muffler (exhaust pipe) has not disconnections, clogging, ruptures, or cracks.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure the exhaust retarder valve does not unsmoothness or stuck.
Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE RETARDER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure there are no foreign substances (oil, soot, etc.) stuck to the interior of the intake air passageway.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the diesel throttle from the vehicle and confirm that it does not snag or is damaged due to the intrusion of foreign substances.
(The throttle valve can be manually moved when it is not energized.)
Check that there is no looseness between the throttle valve and shaft.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the inspection while the engine is stopped to avoid damage.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Activate the VSV for Intake Control / Data List / Intake Air Control Valve Position, Target intake air control valve position
Perform the Active Test.
The Intake Air Control Valve Position follows the Target intake air control valve position.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Perform the confirmation driving pattern.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the diesel throttle body.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>DIESEL THROTTLE BODY>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clean the diesel throttle body.
Replace it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Clean the intake air passageway.
| Proceed to |
|---|
| NEXT |
NEXT
Clean the exhaust retarder valve.
Replace it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the exhaust muffler.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the air hose and pipe.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the air cleaner filter element sub-assembly.
| Proceed to |
|---|
| NEXT |
NEXT