Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2120  Throttle/Pedal Position Sensor/Switch "D" Circuit  P2122  Throttle/Pedal Position Sensor/Switch "D" Circuit Low  P2123  Throttle/Pedal Position Sensor/Switch "D" Circuit High  P2127  Throttle/Pedal Position Sensor/Switch "E" Circuit Low  P2128  Throttle/Pedal Position Sensor/Switch "E" Circuit High  P2138  Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation  


DESCRIPTION

E139697E07
1.521,1.969 2.156,1.417 true 1.521,3.406 2.156,3.979 true 0.938,2.271 1.344,1.417 true 0.958,3.156 1.323,4 true 2.542,1.76 2.969,1.938 0.427,0.177 10 false VCPA 1.396,1.281 1.958,1.49 0.563,0.208 10 false Magnet 1.25,4.01 1.729,4.188 0.479,0.177 10 false Magnet 4,1.938 4.313,2.115 0.313,0.177 10 false 4.55 4.677,1.563 4.906,1.74 0.229,0.177 10 false *1 6.24,1.563 6.479,1.76 0.24,0.198 10 false *2 4,2.125 4.323,2.323 0.323,0.198 10 false 3.89 4.01,2.667 4.333,2.844 0.323,0.177 10 false 1.60 4.01,2.906 4.323,3.083 0.313,0.177 10 false 0.80 4.01,3.031 4.333,3.208 0.323,0.177 10 false 0.41 4.219,3.25 4.375,3.427 0.156,0.177 10 false 0 6.771,3.354 7.094,3.531 0.323,0.177 10 false 110 5.083,3.573 5.979,3.75 0.896,0.177 10 false Usable Range 4.385,3.896 6.865,4.073 2.479,0.177 10 false Accelerator Pedal Opening Angle (deg.) 4.406,4.49 6.688,4.667 2.281,0.177 10 false *1: Accelerator Pedal Fully Released 4.406,4.896 6.771,5.073 2.365,0.177 10 false *2: Accelerator Pedal Fully Depressed 2.573,2.083 2.938,2.26 0.365,0.177 10 false VPA 2.552,2.698 2.958,2.875 0.406,0.177 10 false VPA2 2.573,3.01 2.917,3.188 0.344,0.177 10 false EPA 2.552,3.333 2.969,3.51 0.417,0.177 10 false EPA2 3.99,0.885 5.656,1.271 1.667,0.385 10 false Accelerator Pedal Position Sensor Output Voltage (V) 2.229,1.333 2.771,1.688 0.542,0.354 10 false IC No. 1 2.229,3.927 2.833,4.281 0.604,0.354 10 false IC No. 2


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle/Pedal Position Sensor/Switch "D" Circuit Diagnosis Condition:
·

Engine ECM power supply voltage is in the range of 10 V to 16 V.

·

Engine running.


Malfunction Status:

Both accelerator position sensors No. 1, No. 2 are out of order at the same time.


Malfunction Duration:

-


·

Accelerator pedal assembly

·

Harness or connector

·

ECM


Class C DTC stored
P2122 Throttle/Pedal Position Sensor/Switch "D" Circuit Low Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

No. 1 accelerator position sensor voltage remains at 0.2 V or less for 1 second or more.


Malfunction Duration:

1 seconds or more


·

Accelerator pedal assembly

·

Harness or connector

·

ECM


Class C DTC stored
P2123 Throttle/Pedal Position Sensor/Switch "D" Circuit High Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

No. 1 accelerator position sensor voltage remains at 4.65 V or more for 1 second or more.


Malfunction Duration:

1 seconds or more


·

Accelerator pedal assembly

·

Harness or connector

·

ECM


Class C DTC stored
P2127 Throttle/Pedal Position Sensor/Switch "E" Circuit Low Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

No. 2 accelerator position sensor voltage remains at 0.5 V or less for 1 second or more.


Malfunction Duration:

1 seconds or more


·

Accelerator pedal assembly

·

Harness or connector

·

ECM


Class C DTC stored
P2128 Throttle/Pedal Position Sensor/Switch "E" Circuit High Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

No. 2 accelerator position sensor voltage remains at 4.65 V or more for 1 second or more.


Malfunction Duration:

1 seconds or more


·

Accelerator pedal assembly

·

Harness or connector

·

ECM


Class C DTC stored
P2138 Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation Diagnosis Condition:
The conditions described below continue for at least 5 seconds.
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

The condition that the absolute value of accelerator opening difference between the sensor No. 1 and No. 2 is 20% or more continues for at least 3 seconds.


Malfunction Duration:

3 seconds or more


·

Accelerator pedal assembly

·

Harness or connector

·

ECM


Class C DTC stored

HINT:

After checking for P2120, P2122, P2123, P2127, P2128, and P2138, using the GTS, check the accelerator pedal opening angle and accelerator release position.


Accelerator Pedal Released
(VPA)
Accelerator Pedal Depressed
(VPA)
Accelerator Pedal Released
(VPA2)
Accelerator Pedal Depressed
(VPA2)
Trouble Area
0.6 to 1.0 V 2.8 to 3.6 V 1.4 to 1.8 V 3.6 to 4.4 V Correct accelerator pedal opening angle
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VCPA or VCP2 circuit open
0 to 0.2 V 0 to 0.2 V 1.4 to 1.8 V 3.6 to 4.4 V VPA circuit open or ground short
0.6 to 1.0 V 2.8 to 3.6 V 0 to 0.2 V 0 to 0.2 V VPA2 circuit open or ground short
4.5 to 5.5 V 4.5 to 5.5 V 4.5 to 5.5 V 4.5 to 5.5 V EPA and EPA2 circuit open

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2120 Idle the engine for 1 seconds or more.
P2122
P2123
P2127
P2128
P2138
·

Ignition switch ON, accelerator pedal fully released for 3 seconds or more

·

Ignition switch ON, accelerator pedal depressed halfway for 3 seconds or more

·

Ignition switch ON, accelerator pedal fully depressed for 3 seconds or more



WIRING DIAGRAM

A451434E01
1.771,1.885 2.385,2.083 0.615,0.198 10 false VCPA 1.906,0.802 2.521,1 0.615,0.198 10 false VPA 1.875,1.344 2.49,1.542 0.615,0.198 10 false EPA 1.771,3.031 2.385,3.229 0.615,0.198 10 false VPA2 1.76,3.594 2.375,3.792 0.615,0.198 10 false EPA2 2.396,0.781 2.552,0.979 0.156,0.198 10 false 5 2.396,1.885 2.552,2.083 0.156,0.198 10 false 4 2.406,1.323 2.563,1.521 0.156,0.198 10 false 3 2.427,3.031 2.583,3.229 0.156,0.198 10 false 1 2.427,3.563 2.583,3.76 0.156,0.198 10 false 2 4.125,2.01 4.74,2.208 0.615,0.198 10 false V-50 4.125,3.219 4.74,3.417 0.615,0.198 10 false V-67 4.135,1.469 4.75,1.667 0.615,0.198 10 false V-45 4.125,0.917 4.74,1.115 0.615,0.198 10 false V-47 4.115,3.76 4.729,3.958 0.615,0.198 10 false V-65 4.479,0.917 5.094,1.115 0.615,0.198 10 false A115 4.479,1.469 5.094,1.667 0.615,0.198 10 false A115 4.479,2.01 5.094,2.208 0.615,0.198 10 false A115 4.479,3.229 5.094,3.427 0.615,0.198 10 false A115 4.479,3.771 5.094,3.969 0.615,0.198 10 false A115 4.563,1.802 4.938,2.01 0.375,0.208 10 false 35 4.552,0.698 4.823,0.875 0.271,0.177 10 false 11 4.563,1.25 4.938,1.458 0.375,0.208 10 false 33 4.573,3.01 4.948,3.219 0.375,0.208 10 false 9 4.542,3.563 4.917,3.771 0.375,0.208 10 false 32 4.927,2.01 5.542,2.208 0.615,0.198 10 false VCPA 4.927,0.906 5.542,1.104 0.615,0.198 10 false VPA 4.948,1.458 5.563,1.656 0.615,0.198 10 false EPA 4.927,3.229 5.542,3.427 0.615,0.198 10 false VPA2 4.927,3.771 5.542,3.969 0.615,0.198 10 false EPA2 5.469,4.323 6.083,4.521 0.615,0.198 10 false ECM 0.583,4.167 1.198,4.365 0.615,0.198 10 false F9 0.594,4.406 3.729,5.073 3.135,0.667 10 false Accelerator Pedal Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P2120 is output A
DTC P2122 or P2123 is output B
DTC P2127 or P2128 is output C
DTC P2138 is output D




A

2.REPLACE ACCELERATOR PEDAL ASSEMBLY

B

6.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL ASSEMBLY CONNECTOR)

C

20.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL ASSEMBLY CONNECTOR)

D

34.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL ASSEMBLY CONNECTOR)
2.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal assembly.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2120 is output A
DTCs are not output B




A

4.RESTORE ACCELERATOR PEDAL ASSEMBLY

B

END

4.RESTORE ACCELERATOR PEDAL ASSEMBLY
a.

Restore the accelerator pedal assembly.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ACCELERATOR PEDAL>INSTALLATION


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Replace the ECM with a new one.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECM>REMOVAL


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the GTS on.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P2120 is output A
DTCs are not output B




A

CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
a.

Inspect the circuit between the accelerator pedal assembly and ECM.



B

END

6.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL ASSEMBLY CONNECTOR)
a.

Check the connector connection for the accelerator pedal assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

7.CHECK ACCELERATOR PEDAL ASSEMBLY

NG

19.CONNECT SECURELY
7.CHECK ACCELERATOR PEDAL ASSEMBLY
a.

Check the installation of the accelerator pedal assembly.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the accelerator pedal assembly.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)

NG

18.REPAIR OR REPLACE ACCELERATOR PEDAL ASSEMBLY
8.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the accelerator pedal assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-45 - Body ground and other terminals Always 10 kΩ or higher
V-47 - Body ground and other terminals Always 10 kΩ or higher
V-50 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the accelerator pedal assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-47 - V-50 Always 2 Ω or higher
V-45 - V-50 Always 2 Ω or higher
V-45 - V-47 Always 2 Ω or higher



Result:
Proceed to
OK
NG



OK

10.CHECK ACCELERATOR PEDAL ASSEMBLY

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK ACCELERATOR PEDAL ASSEMBLY
A451435C01
0.167,1.063 0.563,1.365 0.396,0.302 1.708,1.323 1.531,1.75 true 2.115,1.74 1.969,1.333 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.281,1.135 0.594,1.333 0.313,0.198 10 false F9 1.365,1.781 1.677,1.979 0.313,0.198 10 false EPA 2.073,1.771 2.479,1.958 0.406,0.188 10 false VCPA
*a Front view of wire harness connector
(to Accelerator Pedal Assembly)


a.

Disconnect the accelerator pedal assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F9-4 (VCPA) - F9-3 (EPA) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)

NG

8.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
11.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)
A451435C02
0.198,1.052 0.594,1.354 0.396,0.302 1.667,1.365 1.5,1.792 true 2.458,1.792 2.198,1.333 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.313,1.115 0.625,1.313 0.313,0.198 10 false F9 1.292,1.813 1.604,2.01 0.313,0.198 10 false EPA 2.427,1.802 2.844,2.01 0.417,0.208 10 false VPA
*a Front view of wire harness connector
(to Accelerator Pedal Assembly)


a.

Turn the ignition switch off.


b.

Disconnect the accelerator pedal assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-5 (VPA) - F9-3 (EPA) Always 25 to 35 kΩ



Result:
Proceed to
OK
NG



OK

13.CHECK DTC OUTPUT

NG

12.CHECK ACCELERATOR PEDAL ASSEMBLY
12.CHECK ACCELERATOR PEDAL ASSEMBLY
a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-47 - V-50 Always 2 Ω or higher
V-45 - V-50 Always 2 Ω or higher
V-45 - V-47 Always 2 Ω or higher



Result:
Proceed to
OK
NG



OK

13.CHECK DTC OUTPUT

NG

17.REPLACE ACCELERATOR PEDAL ASSEMBLY
13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2122 or P2123 is output A
DTCs are not output B




A

14.REPLACE ECM

B

END

14.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
17.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal assembly.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
18.REPAIR OR REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Repair or replace the accelerator pedal assembly.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the accelerator pedal assembly.



Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
19.CONNECT SECURELY
a.

Connect securely accelerator pedal assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
20.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL ASSEMBLY CONNECTOR)
a.

Check the connector connection for the accelerator pedal assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

21.CHECK ACCELERATOR PEDAL ASSEMBLY

NG

33.CONNECT SECURELY
21.CHECK ACCELERATOR PEDAL ASSEMBLY
a.

Check the installation of the accelerator pedal assembly.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the accelerator pedal assembly.


Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)

NG

32.REPAIR OR REPLACE ACCELERATOR PEDAL ASSEMBLY
22.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Disconnect the accelerator pedal assembly connector.


d.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-50 - Body ground and other terminals Always 10 kΩ or higher
V-65 - Body ground and other terminals Always 10 kΩ or higher
V-67 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)

NG

31.REPAIR OR REPLACE HARNESS OR CONNECTOR
23.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Connect the accelerator pedal assembly connector.


d.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-50 - V-65 Always 2 Ω or higher
V-50 - V-67 Always 2 Ω or higher
V-65 - V-67 Always 2 Ω or higher



Result:
Proceed to
OK
NG



OK

24.CHECK ACCELERATOR PEDAL ASSEMBLY

NG

29.REPAIR OR REPLACE HARNESS OR CONNECTOR
24.CHECK ACCELERATOR PEDAL ASSEMBLY
A451435C03
0.26,1.063 0.656,1.365 0.396,0.302 1.979,1.323 2.281,1.792 true 1,1.76 1.417,1.344 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.385,1.135 0.698,1.333 0.313,0.198 10 false F9 0.833,1.771 1.385,1.99 0.552,0.219 10 false EPA2 2.292,1.813 2.708,1.979 0.417,0.167 10 false VCPA
*a Front view of wire harness connector
(to Accelerator Pedal Assembly)


a.

Disconnect the accelerator pedal assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F9-4 (VCPA) - F9-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)

NG

22.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
25.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)
A451435C05
0.26,1.063 0.656,1.365 0.396,0.302 1.531,1.344 1.833,1.813 true 0.792,1.75 1.208,1.333 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 0.385,1.135 0.698,1.333 0.313,0.198 10 false F9 1.792,1.813 2.344,2.031 0.552,0.219 10 false EPA2 0.646,1.76 1.063,1.927 0.417,0.167 10 false VPA2
*a Front view of wire harness connector
(to Accelerator Pedal Assembly)


a.

Turn the ignition switch off.


b.

Disconnect the accelerator pedal assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F9-1 (VPA2) - F9-2 (EPA2) Always 25 to 35 kΩ



Result:
Proceed to
OK
NG



OK

40.CHECK DTC OUTPUT

NG

26.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)
26.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY CONNECTOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the ECM connector.


c.

Disconnect the accelerator pedal assembly connector.


d.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-50 - V-65 Always 2 Ω or higher
V-50 - V-67 Always 2 Ω or higher
V-65 - V-67 Always 2 Ω or higher



Result:
Proceed to
OK
NG



OK

27.CHECK DTC OUTPUT

NG

30.REPLACE ACCELERATOR PEDAL ASSEMBLY
27.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2127 or P2128 is output A
DTCs are not output B




A

28.REPLACE ECM

B

END

28.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
29.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
30.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal assembly.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
31.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
32.REPAIR OR REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Repair or Replace the accelerator pedal assembly.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the accelerator pedal assembly.



Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
33.CONNECT SECURELY
a.

Connect securely the accelerator pedal assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
34.CHECK CONNECTOR CONNECTION CONDITION (ACCELERATOR PEDAL ASSEMBLY CONNECTOR)
a.

Check the connector connection for the accelerator pedal assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

35.CHECK ACCELERATOR PEDAL ASSEMBLY

NG

39.CONNECT SECURELY
35.CHECK ACCELERATOR PEDAL ASSEMBLY
a.

Turn the ignition switch off.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Turn the ignition switch to ON.


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the voltage between each terminal when the accelerator pedal is operated from fully released to fully depressed.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Sensor 1:
V-47 - Body ground
Ignition switch ON
Accelerator Pedal (Released→Depressed)
Difference in voltage between sensor 1 and sensor 2:
0.4 to 1.2 V
Sensor 2:
V-67 - Body ground



Result:
Proceed to
OK
NG



OK

36.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)

NG

38.REPLACE ACCELERATOR PEDAL ASSEMBLY
36.CHECK HARNESS OR CONNECTOR (ACCELERATOR PEDAL ASSEMBLY - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the accelerator pedal assembly connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Turn the ignition switch to ON.


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
V-47 - Body ground Ignition switch ON 0 V
V-67 - Body ground Ignition switch ON 0 V



Result:
Proceed to
OK
NG



OK

END

NG

37.REPLACE ECM
37.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
38.REPLACE ACCELERATOR PEDAL ASSEMBLY
a.

Replace the accelerator pedal assembly.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
39.CONNECT SECURELY
a.

Connect securely the accelerator pedal assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

40.CHECK DTC OUTPUT
40.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END