Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2146  Fuel Injector Group "A" Supply Voltage Circuit/Open  P2147  Fuel Injector Group "A" Supply Voltage Circuit Low  P2148  Fuel Injector Group "A" Supply Voltage Circuit High  P2149  Fuel Injector Group "B" Supply Voltage Circuit/Open  P2150  Fuel Injector Group "B" Supply Voltage Circuit Low  P2151  Fuel Injector Group "B" Supply Voltage Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2146 Fuel Injector Group "A" Supply Voltage Circuit/Open Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Immediately after starting injection or during stopping injection.

·

Starter is not in operation.

·

DTC related to actuator of injector is not detected.


Malfunction Status:
·

Fuel injector driver circuit 1 remains nonenergized for at least 2 seconds with the engine runs at 600 rpm.


Malfunction Duration:

2 seconds or more


·

ECM

·

Harness or connector


Class A DTC stored
P2147 Fuel Injector Group "A" Supply Voltage Circuit Low Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Immediately after starting injection or during stopping injection.

·

Starter is not in operation.

·

DTC related to actuator of injector is not detected.


Malfunction Status:

When the fuel injector driver circuit 1 voltage is smaller than 1.2 V, the fail count is detected with the full count. (When the engine speed is 600 rpm: 1 second * Varies according to engine speed)


Malfunction Duration:

1 second or more


·

ECM

·

Injector internal coil

·

Harness or connector


Class A DTC stored
P2148 Fuel Injector Group "A" Supply Voltage Circuit High Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Immediately after starting injection or during stopping injection.

·

Starter is not in operation.

·

DTC related to actuator of injector is not detected.


Malfunction Status:

Voltage of fuel injector driver circuit 1 remains 4.8 V or more for at least 1 second with the engine runs at 600 rpm.


Malfunction Duration:

1 second or more


·

ECM

·

Injector internal coil

·

Harness or connector


Class A DTC stored
P2149 Fuel Injector Group "B" Supply Voltage Circuit/Open Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Immediately after starting injection or during stopping injection.

·

Starter is not in operation.

·

DTC related to actuator of injector is not detected.


Malfunction Status:

Fuel injector driver circuit 2 remains nonenergized for at least 2 seconds with the engine runs at 600 rpm.


Malfunction Duration:

2 seconds or more


·

ECM

·

Harness or connector


Class A DTC stored
P2150 Fuel Injector Group "B" Supply Voltage Circuit Low Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Immediately after starting injection or during stopping injection.

·

Starter is not in operation.

·

DTC related to actuator of injector is not detected.


Malfunction Status:

When the fuel injector driver circuit 2 voltage is smaller than 1.2 V, the fail count is detected with the full count. (When the engine speed is 600 rpm: 1 second * Varies according to engine speed)


Malfunction Duration:

1 second or more


·

ECM

·

Injector internal coil

·

Harness or connector


Class A DTC stored
P2151 Fuel Injector Group "B" Supply Voltage Circuit High Diagnosis Condition:
·

Ignition switch ON.

·

Battery voltage is in the range of 10 V to 16 V

·

Immediately after starting injection or during stopping injection.

·

Starter is not in operation.

·

DTC related to actuator of injector is not detected.


Malfunction Status:

Voltage of fuel injector driver circuit 2 remains 4.8 V or more for at least 1 second with the engine runs at 600 rpm.


Malfunction Duration:

1 second or more


·

ECM

·

Injector internal coil

·

Harness or connector


Class A DTC stored

MONITOR DESCRIPTION

·

The ECM controls the fuel injection quantity according to the injector valve-open interval.

·

The valve-open interval is adjusted by the magnetic valve.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2146
P2147
P2148
P2149
P2150
P2151
Idle the engine for 2 seconds or more.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P2146 or P2149 is output A
DTC P2147 or P2150 is output B
DTC P2148 or P2151 is output C
DTCs other than P2146, P2147, P2148, P2149, P2150 or P2151 are output D




A

2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)

B

8.CHECK CONNECTOR CONNECTION CONDITION (INJECTOR ASSEMBLY)

C

19.CHECK CONNECTOR CONNECTION CONDITION (INJECTOR ASSEMBLY)

D

2.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)
A407531C03
0.427,1.042 0.833,1.333 0.406,0.292 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.531,1.115 0.865,1.313 0.333,0.198 10 false Bi1
*a Front view of wire harness connector
(to Injector Harness 8P Connector)


a.

Disconnect the injector harness 8P connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Injector Assembly
Tester Connection Condition Specified Condition
Bi1-2 - Body ground and other terminals Ignition switch ON Below 14 V
Bi1-4 - Body ground and other terminals Ignition switch ON Below 14 V
Bi1-6 - Body ground and other terminals Ignition switch ON Below 14 V
Bi1-8 - Body ground and other terminals Ignition switch ON Below 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)
3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E-14 - Body ground Ignition switch ON Below 14 V
E-18 - Body ground Ignition switch ON Below 14 V
E-34 - Body ground Ignition switch ON Below 14 V
E-38 - Body ground Ignition switch ON Below 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P2146 or P2149 is output A
DTC P2146 or P2149 is not output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
8.CHECK CONNECTOR CONNECTION CONDITION (INJECTOR ASSEMBLY)
a.

Check the connector connection for the injector assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - ECM)

NG

18.CONNECT SECURELY
9.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - ECM)
A407531C04
0.427,1.042 0.833,1.333 0.406,0.292 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.521,1.115 0.854,1.313 0.333,0.198 10 false Bi1
*a Front view of wire harness connector
(to Injector Harness 8P Connector)


a.

Disconnect the injector harness 8P connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Injector Assembly
Tester Connection Condition Specified Condition
Bi1-1 - Body ground Always 10 kΩ or higher
Bi1-2 - Body ground Always 10 kΩ or higher
Bi1-3 - Body ground Always 10 kΩ or higher
Bi1-4 - Body ground Always 10 kΩ or higher
Bi1-5 - Body ground Always 10 kΩ or higher
Bi1-6 - Body ground Always 10 kΩ or higher
Bi1-7 - Body ground Always 10 kΩ or higher
Bi1-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - INJECTOR ASSEMBLLY)

NG

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - INJECTOR ASSEMBLLY)
A407233C09
0.427,1.042 0.833,1.333 0.406,0.292 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.521,1.115 0.854,1.313 0.333,0.198 10 false Bi1
*a Front view of wire harness connector
(to Injector Harness 8P Connector)


a.

Disconnect the injector harness 8P connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Injector Assembly
Tester Connection Condition Specified Condition
Bi1-2 - Body ground Always 10 kΩ or higher
Bi1-1 - Body ground Always 10 kΩ or higher
Bi1-4 - Body ground Always 10 kΩ or higher
Bi1-3 - Body ground Always 10 kΩ or higher
Bi1-6 - Body ground Always 10 kΩ or higher
Bi1-5 - Body ground Always 10 kΩ or higher
Bi1-8 - Body ground Always 10 kΩ or higher
Bi1-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.INSPECT INJECTOR ASSEMBLY

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.INSPECT INJECTOR ASSEMBLY
a.

Disconnect the injector assembly connector.


b.

Inspect the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>INSPECTION


c.
A417903C01
0.448,0.25 0.76,0.406 0.313,0.156 10 false *1 2.542,0.219 2.854,0.375 0.313,0.156 10 false *2
*1 Injector Assembly
*2 Megohmmeter


Measure the resistance between each terminal of the injector and injector body.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Always 10 MΩ or higher
2 - Body ground Always 10 MΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

15.REPLACE INJECTOR ASSEMBLY
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P2147 or P2150 is output A
DTCs are not output B




A

13.REPLACE ECM

B

END

13.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

15.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
17.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
18.CONNECT SECURELY
a.

Connect securely the injector assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
19.CHECK CONNECTOR CONNECTION CONDITION (INJECTOR ASSEMBLY)
a.

Check the connector connection for the injector assembly connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)

NG

31.CONNECT SECURELY
20.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Injector Assembly
Tester Connection Condition Specified Condition
E-14 - Body ground Ignition switch ON Below 14 V
E-18 - Body ground Ignition switch ON Below 14 V
E-34 - Body ground Ignition switch ON Below 14 V
E-38 - Body ground Ignition switch ON Below 14 V



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)

NG

30.REPAIR OR REPLACE HARNESS OR CONNECTOR
21.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY POWER SORCE)
A407531C05
0.427,1.042 0.833,1.333 0.406,0.292 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.521,1.115 0.854,1.313 0.333,0.198 10 false Bi1
*a Front view of wire harness connector
(to Injector Harness 8P Connector)


a.

Disconnect the injector harness 8P connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Injector Assembly
Tester Connection Condition Specified Condition
Bi1-2 - Body ground Ignition switch ON Below 14 V
Bi1-4 - Body ground Ignition switch ON Below 14 V
Bi1-6 - Body ground Ignition switch ON Below 14 V
Bi1-8 - Body ground Ignition switch ON Below 14 V



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - INJECTOR ASSEMBLLY)

NG

29.REPAIR OR REPLACE HARNESS OR CONNECTOR
22.CHECK HARNESS AND CONNECTOR (INJECTOR HARNESS 8P CONNECTOR - INJECTOR ASSEMBLLY)
A407233C10
0.427,1.042 0.833,1.333 0.406,0.292 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.521,1.115 0.854,1.313 0.333,0.198 10 false Bi1
*a Front view of wire harness connector
(to Injector Harness 8P Connector)


a.

Disconnect the injector harness 8P connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Injector Assembly
Tester Connection Condition Specified Condition
Bi1-2 - Body ground Always 10 kΩ or higher
Bi1-4 - Body ground Always 10 kΩ or higher
Bi1-6 - Body ground Always 10 kΩ or higher
Bi1-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT INJECTOR ASSEMBLY

NG

28.REPAIR OR REPLACE HARNESS OR CONNECTOR
23.INSPECT INJECTOR ASSEMBLY
a.

Disconnect the injector assembly connector.


b.

Inspect the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>INSPECTION


c.
A417903C01
0.448,0.25 0.76,0.406 0.313,0.156 10 false *1 2.542,0.219 2.854,0.375 0.313,0.156 10 false *2
*1 Injector Assembly
*2 Megohmmeter


Measure the resistance between each terminal of the injector and injector body.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Body ground Always 10 MΩ or higher
2 - Body ground Always 10 MΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK DTC OUTPUT

NG

27.REPLACE INJECTOR ASSEMBLY
24.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P2148 or P2151 is output A
DTCs are not output B




A

25.REPLACE ECM

B

END

25.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
26.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

27.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
28.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
29.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
30.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
31.CONNECT SECURELY
a.

Connect securely the injector assembly connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT