Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2201  NOx Sensor Circuit Range/Performance Bank 1 Sensor 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2201 NOx Sensor Circuit Range/Performance Bank 1 Sensor 1 Diagnosis Condition:
·

The No. 1 nitrogen oxides sensor is operating.

·

5 seconds or more elapses after completion of DPR operation.

·

DOC monitor (DTC P0421) is not detected.

·

300 seconds or more after the engine starts.

·

Engine coolant temperature is higher than 60°C (140°F).

·

A change in NOx value compared to the calculated NOx value is 0.3 or less.

·

Atmospheric pressure is 75 kPa or more.

·

The value of the ambient air temperature sensor is in the range of -7 to 40°C (19.4 to 104°F)


Malfunction Status:

Compare actual NOx (from No. 1 nitrogen oxides sensor) with calculated NOx No. 1 (from ECM)


Malfunction Duration:

5 seconds or more


·

Harness or connector

·

No. 1 nitrogen oxides sensor

·

Mass air flow meter

·

Manifold absolute pressure sensor

·

Engine coolant temperature sensor

·

Intake air temperature sensor (for intake manifold side)


Class A DTC stored

MONITOR DESCRIPTION

·

No. 1 nitrogen oxides sensor confirms correct value by comparing actual NOx value with the model value calculated by the ECM.

·

NOx model value is calculated according to the engine's state and properties.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2201 PM forced regeneration

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P2201 is output A
DTCs other than P2201 are output B



HINT:

Select (Engine) and check if any DTC other than P2201 (for example P2202, P2209, U029D) has been detected.



A

2.CHECK NO. 1 NITROGEN OXIDES SENSOR

B

2.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Remove the No. 1 nitrogen oxides sensor and No. 2 nitrogen oxides sensor, and install them in their opposite location.


Result:
Proceed to
NEXT



NEXT

3.PERFORM PM FORCED REGENERATION
3.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read Current DTCs.

Result:
Result Proceed to
DTC P2201 is not output A
DTC P2201 is output B




A

5.REPLACE NO. 1 NITROGEN OXIDES SENSOR

B

6.CHECK ENGINE COOLANT TEMPERATURE SENSOR
5.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
6.CHECK ENGINE COOLANT TEMPERATURE SENSOR
a.

Check the installation of the engine coolant temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of engine coolant temperature sensor.


Result:
Proceed to
OK
NG



OK

7.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

23.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
7.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
a.

Result:
Proceed to
OK
NG



OK

8.CHECK MASS AIR FLOW METER

NG

22.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
8.CHECK MASS AIR FLOW METER
a.

Check the installation of the mass air flow meter.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the mass air flow meter.


Result:
Proceed to
OK
NG



OK

9.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

21.REPAIR OR REPLACE MASS AIR FLOW METER
9.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Check the installation of the manifold absolute pressure sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the manifold absolute pressure sensor.


Result:
Proceed to
OK
NG



OK

10.CHECK READ VALUE USING GTS (ACTUAL BOOST PRESSURE)

NG

20.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
10.CHECK READ VALUE USING GTS (ACTUAL BOOST PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Actual Boost Pressure.


e.

Race the engine from idle to NMR and verify that the boost pressure output signal varies.


f.

Read the value.


Standard:

There is no abnormal change in the sensor output signal.

(The pressure sensor signal response changes according to the engine speed)


Result:
Proceed to
OK
NG



OK

11.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

19.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
11.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Check the installation of the intake air temperature sensor (for intake manifold side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of intake air temperature sensor (for intake manifold side).


Result:
Proceed to
OK
NG



OK

12.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

18.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
12.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Inspect the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

13.REPLACE NO. 1 NITROGEN OXIDES SENSOR

NG

17.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
13.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2201 is output A
DTCs are not output B




A

15.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)

B

END

15.REPLACE DCU (EMISSION CONTROL ECU ASSEMBLY)
a.

Replace the DCU (emission control ECU assembly).

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>UREA PUMP CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

17.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Replace the intake air temperature sensor (for intake manifold side).


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
18.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Repair or replace the intake air temperature sensor (for intake manifold side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intake manifold side).



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
19.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
20.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Repair or replace the manifold absolute pressure sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the manifold absolute pressure sensor.



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
21.REPAIR OR REPLACE MASS AIR FLOW METER
a.

Repair or replace the mass air flow meter.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
22.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor.


Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT
23.REPAIR OR REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Repair or replace the engine coolant temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the engine coolant temperature sensor.



Result:
Proceed to
NEXT



NEXT

16.CHECK DTC OUTPUT