Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P242C  Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3  P242D  Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P242C Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3 Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Engine is running at engine speed over 490 rpm for at least 5 seconds.


Malfunction Status:

Voltage of the No. 3 exhaust gas temperature sensor remains less than 0.057 V for 3 seconds.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

No. 3 exhaust gas temperature sensor

·

ECM


Class B1 DTC stored
P242D Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3 Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Engine is running at engine speed over 490 rpm for at least 5 seconds.


Malfunction Status:

Voltage of the No. 3 exhaust gas temperature sensor remains at 4.98 V or higher (-46°C (-50.8°F) or lower) for 3 seconds.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

No. 3 exhaust gas temperature sensor

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

·

The No. 3 exhaust gas temperature sensor consistently detects exhaust gas temperature.

·

A reading taken by the No. 3 exhaust gas temperature sensor is used to control DPR regeneration.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P242C Idle the engine for 3 seconds or more.
P242D Idle the engine for 60 seconds or more.

WIRING DIAGRAM

A407162E28
5.667,2.417 6.74,2.615 1.073,0.198 10 false ECM 4.469,0.906 5.542,1.104 1.073,0.198 10 false V-69 4.469,1.49 5.542,1.688 1.073,0.198 10 false V-46 4.823,0.917 5.896,1.115 1.073,0.198 10 false A115 4.813,1.49 5.885,1.688 1.073,0.198 10 false B142 1.479,0.813 2.552,1.01 1.073,0.198 10 false THC3 5.26,1.469 6.333,1.667 1.073,0.198 10 false E2 1.969,0.771 3.042,0.969 1.073,0.198 10 false 1 1.969,1.323 3.042,1.521 1.073,0.198 10 false 2 0.531,2.094 1.604,2.292 1.073,0.198 10 false A111 0.531,2.292 3.25,2.563 2.719,0.271 10 false No. 3 Exhaust Gas Temperature Sensor 4.917,0.688 5.99,0.885 1.073,0.198 10 false 22 4.875,1.292 5.948,1.49 1.073,0.198 10 false 107 5.281,0.927 6.354,1.125 1.073,0.198 10 false THO 1.646,1.375 2.719,1.573 1.073,0.198 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection for the No. 3 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

13.CONNECT SECURELY
2.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 3 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 3 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

12.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
3.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

11.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
4.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
A407251C25
0.604,0.792 1.208,1.156 0.604,0.365 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.75,0.896 1.365,1.094 0.615,0.198 10 false A111
*a Front view of wire harness connector
(to No. 3 Exhaust Gas Temperature Sensor)


a.

Disconnect the No. 3 exhaust gas temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A111-1 (THC3) - A111-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

5.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the No. 3 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - Body ground and other terminals Always 10 kΩ or higher
V-69 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the No. 3 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - V-69 Always (20°C) 13.7 to 29.8 kΩ
V-46 - V-69 Always (50°C) 7.13 to 13.7 kΩ
V-46 - V-69 Always (80°C) 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P242C or P242D is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
11.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 3 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 3 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.CONNECT SECURELY
a.

Connect securely the No. 3 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END