Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P244B  Particulate Filter Differential Pressure Too High Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P244B Particulate Filter Differential Pressure Too High Bank 1 Diagnosis Condition:
·

Ignition switch ON

·

Exhaust brake is inactive for 3 seconds or more.

·

The calculated soot deposit is 0 to 11% after an automatic DPR regeneration.

·

The accumulated soot emission due to DPR activation is 15 kg or more.

·

Calculated exhaust gas flow rate of 205 L/s or higher

Under the conditions above, the accumulated exhaust gas flow rate is above 250000 L.


Malfunction Status:
·

Judge when soot deposit accumulated by ECM reaches the warning level judgment value (5.2 g/L).

·

A judgment is made when the accumulation (differential pressure/exhaust gas flow rate) is above 0.07.


Malfunction Duration:

1 second or more


P2463 not in past DTCs
·

Monolithic converter assembly

·

Differential pressure sensor

·

Blockage and damage in differential pressure sensor pipe or hose


P2463 in past DTCs
·

DPR indicator light

·

DPR switch

·

Harness or connector

·

Neutral start switch assembly

·

Accelerator pedal assembly

·

Injector assembly


Class B1 DTC stored

MONITOR DESCRIPTION

·

The ECM always calculates and integrates the soot discharge quantity from the engine.

·

The ECM decides the DPR regeneration mode based on the soot accumulation quantity.

·

The soot accumulation quantity has exceeded the allowable regeneration quantity.

·

DPR regeneration failure is detected on the basis of the values obtained from the differential pressure sensor and the No. 4 exhaust gas temperature sensor.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P244B PM forced regeneration

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

After using this DTC to check and repair, check the engine oil amount.

·

Replace the engine oil if it exceeds the upper level of the level gauge (X mark: 25 mm over the upper level of a standard level gauge).



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
P244B is output (P2463 not in past DTCs) A
P244B is output (P2463 in past DTCs) B
DTC P244B and other DTCs are output C




A

2.CHECK FREEZE FRAME DATA (PM DEPOSITION VALUE)

B

25.CHECK MANUAL REGENERATION REQUEST (DPR LIGHT CONTINUED TO BLINK)

C

2.CHECK FREEZE FRAME DATA (PM DEPOSITION VALUE)
a.

Check PM Deposition Value in the freeze frame data.

NOTICE:

For the P244B code, there are two types of DTC detection conditions. The inspection method depends on these conditions. Check that the amount of soot deposited from GTS report, and operate using the method that matches the detection condition.



Result:
Result Proceed to
PM Deposition Value is less than 5.2 g/L A
PM Deposition Value is more than 5.2 g/L B



A

3.CHECK MONOLITHIC CONVERTER ASSEMBLY

B

25.CHECK MANUAL REGENERATION REQUEST (DPR LIGHT CONTINUED TO BLINK)
3.CHECK MONOLITHIC CONVERTER ASSEMBLY
a.

Remove the monolithic converter assembly and check that there is no soot leaking at the rear edge of the monolithic converter assembly, no damage, and no other abnormality.


Result:
Proceed to
OK
NG



OK

4.INSPECT DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

NG

10.REPLACE MONOLITHIC CONVERTER ASSEMBLY
4.INSPECT DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

Result:
Proceed to
OK
NG



OK

5.CHECK NO. 1 EXHAUST PIPE CONVERTER ASSEMBLY

NG

9.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
5.CHECK NO. 1 EXHAUST PIPE CONVERTER ASSEMBLY
a.

Check the differential pressure sensor pipe for clogging, cracks, and other damage.


Result:
Proceed to
OK
NG



OK

6.CHECK DIFFERENTIAL PRESSURE SENSOR HOSE

NG

8.REPAIR OR REPLACE NO. 1 EXHAUST PIPE CONVERTER ASSEMBLY
6.CHECK DIFFERENTIAL PRESSURE SENSOR HOSE
a.

Check the differential pressure sensor hose for clogging, cracks, and other damages.


Result:
Proceed to
OK
NG



OK

END

NG

7.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR HOSE
7.REPAIR OR REPLACE DIFFERENTIAL PRESSURE SENSOR HOSE
a.

Repair or replace the differential pressure sensor hose.


Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
8.REPAIR OR REPLACE NO. 1 EXHAUST PIPE CONVERTER ASSEMBLY
a.

Repair or replace the No. 1 exhaust pipe converter asembly (differential pressure sensor pipe).


Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
9.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Replace the differential pressure sensor assembly.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
10.REPLACE MONOLITHIC CONVERTER ASSEMBLY
a.

Replace the monolithic converter assembly and the burner nozzle and clean the igniter.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>MONOLITHIC CONVERTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

11.PERFORM BASIC INSPECTION
11.PERFORM BASIC INSPECTION
a.

Turn the ignition switch to ON.


b.

Inspect the engine parts and systems based on the engine basic inspection sheet.


Result:
Proceed to
OK
NG



OK

12.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

24.REPAIR OR REPLACE TROUBLE AREAS
12.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the connection of the No. 3 exhaust gas temperature sensor connector (looseness and poor contact).


Result:
Proceed to
OK
NG



OK

13.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

23.CONNECT SECURELY
13.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 3 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of No. 3 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

14.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

22.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
14.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

15.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

21.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
15.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the connection of the No. 4 exhaust gas temperature sensor connector (looseness and poor contact).


Result:
Proceed to
OK
NG



OK

16.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

20.CONNECT SECURELY
16.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 4 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of No. 4 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

17.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

19.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
17.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

END

NG

18.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
18.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
19.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 4 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 4 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
20.CONNECT SECURELY
a.

Connect securely the No. 4 exhaust gas temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
21.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
22.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 3 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 3 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
23.CONNECT SECURELY
a.

Connect securely the No. 3 exhaust gas temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
24.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the faulty part.

HINT:

If the air flow meter is defective, go to step 12.



Result:
Proceed to
NEXT



NEXT

12.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
25.CHECK MANUAL REGENERATION REQUEST (DPR LIGHT CONTINUED TO BLINK)
a.

Start the engine.


b.

Check the blinking of the DPR indicator light in the combination meter and the DPR switch light.


Result:
Proceed to
OK
NG



OK

26.CLEAR DTC

NG

29.INSPECT DPR INDICATOR LIGHT
26.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

27.PERFORM PM FORCED REGENERATION
27.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.



Result:
Result Proceed to
Manual forced regeneration started normally A
Manual forced regeneration does not start normally B



A

28.PERFORM PM FORCED REGENERATION

B

32.CHECK DPR INDICATOR
28.PERFORM PM FORCED REGENERATION
a.

Check if the regeneration normally completes. (Do not activate the accelerator or change the gear position. Or, the regeneration will be aborted.)


b.

The regeneration is complete if idling speed returns to normal and the number of the soot bars in the meter returns to 0.


Result:
Proceed to
OK
NG



OK

END

NG

30.CHECK DTC OUTPUT
29.INSPECT DPR INDICATOR LIGHT
a.

Inspect the combination meter connector (looseness, poor contact).


b.

Check for broken bulb.


c.

Inspect the harness for disconnections and short-circuits.


Result:
Proceed to
OK
NG



OK

26.CLEAR DTC

NG

31.REPAIR OR REPLACE TROUBLE AREAS
30.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P244A is output A
DTCs are not output B




A

B

32.CHECK DPR INDICATOR
31.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the faulty part.


Result:
Proceed to
NEXT



NEXT

26.CLEAR DTC
32.CHECK DPR INDICATOR
a.

Inspect the combination meter connector (looseness, poor contact).


b.

Inspect the switch unit.


c.

Inspect the harness for disconnections and short-circuits.


Result:
Proceed to
OK
NG



OK

33.CHECK EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY OR PARK/NEWTRAL POSITION SWITCH ASSEMBLY

NG

41.REPAIR OR REPLACE TROUBLE AREAS
33.CHECK EXHAUST BRAKE NEUTRAL SWITCH ASSEMBLY OR PARK/NEWTRAL POSITION SWITCH ASSEMBLY
a.

Check the installation of the switch connector.


b.

Inspect the harness for disconnections and short-circuits.


c.

Inspect the switch assembly.

for Manual Transmission:
·

Inspect the exhaust brake neutral switch assembly.

Click hereBrake>EXHAUST BRAKE>EXHAUST BRAKE NEUTRAL SWITCH>INSPECTION


for Automatic Transmission:
·


Result:
Proceed to
OK
NG



OK

34.CHECK ACCELERATOR PEDAL ASSEMBLY

NG

40.REPAIR OR REPLACE TROUBLE AREAS
34.CHECK ACCELERATOR PEDAL ASSEMBLY
a.

Check the installation of the accelerator pedal assembly connector.


b.

Inspect the harness for disconnections and short-circuits.



Result:
Proceed to
OK
NG



OK

35.READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)

NG

39.REPAIR OR REPLACE TROUBLE AREAS
35.READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


e.

Read the value displayed on the GTS.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG


HINT:

If normal, the DPR switch was not pressed.



OK

36.REPLACE MONOLITHIC CONVERTER ASSEMBLY

NG

37.REPLACE INJECTOR ASSEMBLY
36.REPLACE MONOLITHIC CONVERTER ASSEMBLY
a.

Replace the monolithic converter assembly.


b.

DPR manual regenerating the diagnosis procedure will be complete.


Result:
Proceed to
NEXT



NEXT

END

37.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

38.CHECK DTC OUTPUT
38.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

39.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

26.CLEAR DTC
40.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

26.CLEAR DTC
41.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the trouble areas.


Result:
Proceed to
NEXT



NEXT

26.CLEAR DTC