Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P246F  Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 4  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P246F Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 4 Diagnosis Condition:
Engine Start-up:
·

Battery voltage is in the range of 10 V to 16 V

·

The engine speed remains at 500 rpm or more for 5 seconds or more.

·

The difference between the engine coolant temperature and intake air temperature is 10°C (50°F) or less within 10 seconds after the engine start.

·

The difference between the engine coolant temperatures before the engine start and after (present) is 20°C (68°F) or more.

·

Engine coolant temperature is at least -10°C (14°F).

·

Intake air temperature is at least -10°C (14°F).


While Driving:
·

At least 10 seconds has elapsed since engine was started.

·

The exhaust gas flow rate is 120 kg/h or more and the accumulation is 2 kg or more.

·

Cumulative exhaust gas flow amount of 20 Kg or more with after regeneration.

·

After the above:

-

Battery voltage is in the range of 10 V to 16 V

-

The engine speed remains at 500 rpm or more for 5 seconds or more.

-

Engine speed 1000 rpm or more

-

Exhaust fuel addition injector amount 30 mm3/st or more

-

Exhaust gas flow rate 120 kg/h or more

-

The difference between the engine coolant temperature and intake air temperature is more than 10°C (50°F).


·

In addition, the following conditions continue for at least 10 seconds:

-

Engine speed variation is within 25 rpm

-

Exhaust fuel addition injector rate variation is within 5 mm3/st

-

Vehicle speed 18.8 mph or more



Malfunction Status:
Engine Start-up:

Difference between No. 1 exhaust gas temperature sensor and No. 2 exhaust gas temperature sensor stays less than 70°C (158°F), and difference between No. 2 exhaust gas temperature sensor and No. 3 exhaust gas temperature sensor stays less than 70°C (158°F), and difference between No. 3 exhaust gas temperature sensor and No. 4 exhaust gas temperature sensor stays more than 70°C (158°F).

The conditions described above remain for 1 second or more.


While Driving:

Difference between calculated No. 4 exhaust gas temperature sensor - actual No. 4 exhaust gas temperature sensor stays more than 100°C (212°F) for 3 seconds.


Malfunction Duration:
Engine Start-up:

1 second or more


While Driving:

3 seconds or more


·

No. 4 exhaust gas temperature sensor

·

Harness or connector

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

·

The exhaust gas temperature is constantly detected by the No. 4 exhaust gas temperature sensor.

·

The value of the No. 4 exhaust gas temperature sensor is used to control DPR regeneration.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P246F Drive for a certain amount of time after starting the engine.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK EXHAUST PIPE
a.

Check for exhaust pipe crack, exhaust gas leak (soot contamination) and improper coupling flange tightening.


Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR)

NG

28.REPAIR OR REPLACE EXHAUST PIPE
2.CHECK CONNECTOR CONNECTION CONDITION (NO. 4 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection for the No. 4 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

27.CONNECT SECURELY
3.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 4 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 4 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

26.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
4.INSPECT NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR

NG

25.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
5.CHECK NO. 4 EXHAUST GAS TEMPERATURE SENSOR
A451440C06
0.667,0.708 1.146,1.01 0.479,0.302 2.198,1.656 1.792,1.292 true 1.104,1.708 1.521,1.292 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 0.76,0.781 1.49,1.219 0.729,0.438 10 false A112 2.188,1.698 2.917,2.135 0.729,0.438 10 false THSO 0.948,1.719 1.677,2.156 0.729,0.438 10 false E2
*a Front view of wire harness connector
(to No. 4 Exhaust Gas Temperature Sensor)


a.

Disconnect the No. 4 exhaust gas temperature sensor.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A112-1 (THSO) - A112-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

6.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 EXHAUST GAS TEMPERATURE SENSOR)

NG

19.CHECK HARNESS OR CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
6.CHECK CONNECTOR CONNECTION CONDITION (NO. 3 EXHAUST GAS TEMPERATURE SENSOR)
a.

Check the connector connection for the No. 3 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

7.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

18.CONNECT SECURELY
7.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 3 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the No. 3 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

17.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
8.INSPECT NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR

NG

16.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
9.CHECK NO. 3 EXHAUST GAS TEMPERATURE SENSOR
A451440C10
0.604,0.792 1.021,1.094 0.417,0.302 2.135,1.708 1.802,1.302 true 1.042,1.719 1.542,1.292 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.667,0.875 1.688,1.427 1.021,0.552 10 false A111 0.844,1.729 1.302,1.927 0.458,0.198 10 false E2 2.083,1.74 2.542,1.938 0.458,0.198 10 false THC3
*a Front view of wire harness connector
(to No. 3 Exhaust Gas Temperature Sensor)


a.

Disconnect the No. 3 exhaust gas temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A111-1 (THC3) - A111-2 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

10.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)
10.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the No. 3 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - Body ground and other terminals Always 10 kΩ or higher
V-69 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

15.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.CHECK HARNESS OR CONNECTOR (NO. 3 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the No. 3 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - V-69 Always (20°C) 13.7 to 29.8 kΩ
V-46 - V-69 Always (50°C) 7.13 to 13.7 kΩ
V-46 - V-69 Always (80°C) 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

12.CHECK DTC OUTPUT

NG

14.REPAIR OR REPLACE HARNESS OR CONNECTOR
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.


e.

Turn the ignition switch off for 30 seconds or more.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P246F is output A
DTCs are not output B




A

13.REPLACE ECM

B

29.CHECK DTC OUTPUT
13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
14.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
15.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
16.REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 3 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
17.REPAIR OR REPLACE NO. 3 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 3 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 3 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
18.CONNECT SECURELY
a.

Connect securely the No. 3 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
19.CHECK HARNESS OR CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the No. 4 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - Body ground and other terminals Always 10 kΩ or higher
V-57 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS OR CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

24.REPAIR OR REPLACE HARNESS OR CONNECTOR
20.CHECK HARNESS OR CONNECTOR (NO. 4 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the No. 4 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C18
1.479,0.083 1.927,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.656,0.135 1.969,0.333 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-46 - V-57 Always (20°C) 13.7 to 29.8 kΩ
V-46 - V-57 Always (50°C) 7.13 to 13.7 kΩ
V-46 - V-57 Always (80°C) 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

21.CHECK DTC OUTPUT

NG

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
21.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P246F is output A
DTCs are not output B




A

22.REPLACE ECM

B

END

22.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
23.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
24.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
25.REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 4 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
26.REPAIR OR REPLACE NO. 4 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 4 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 4 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
27.CONNECT SECURELY
a.

Connect securely the No. 4 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
28.REPAIR OR REPLACE EXHAUST PIPE
a.

Repair the exhaust pipe.

HINT:

Replace it as needed.



Result:
Proceed to
NEXT



NEXT

29.CHECK DTC OUTPUT
29.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END