Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2A00  A/F (O2) Sensor Circuit Range/Performance Bank 1 Sensor 1  P2A01  A/F (O2) Sensor Circuit Range/Performance Bank 1 Sensor 2  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2A00 A/F (O2) Sensor Circuit Range/Performance Bank 1 Sensor 1 Diagnosis Condition:
·

Functioning normally sensors:

-

No. 1 nitrogen oxides sensor

-

No. 2 nitrogen oxides sensor

-

Crankshaft position sensor

-

Camshaft position sensor



Malfunction Status:

No. 1 nitrogen oxides sensor output deviates 10% or more from the oxygen concentration (20.9%) of the atmosphere.


Malfunction Duration:

-


No. 1 nitrogen oxides sensor Class C DTC stored
P2A01 A/F (O2) Sensor Circuit Range/Performance Bank 1 Sensor 2 Diagnosis Condition:
·

Functioning normally sensors:

-

No. 1 nitrogen oxides sensor

-

No. 2 nitrogen oxides sensor

-

Crankshaft position sensor

-

Camshaft position sensor



Malfunction Status:

No. 2 nitrogen oxides sensor output deviates 10% or more from the oxygen concentration (20.9%) of the atmosphere.


Malfunction Duration:

-


No. 2 nitrogen oxides sensor Class C DTC stored

MONITOR DESCRIPTION

Nitrogen oxides sensor measures concentrations of exhaust gas and oxygen in the exhaust line.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2A00
P2A01
Engine speed 1000 rpm or more for 30 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2A00 is output A
DTC P2A01 is output B
Except above C


HINT:

If any DTCs other than P2201, P029D or P029E are output, troubleshoot those DTCs first.




A

2.INSPECT EXHAUST PIPE

B

8.INSPECT EXHAUST PIPE

C

2.INSPECT EXHAUST PIPE
a.

Check for dirt, soot, clogging, leakage, or damage in the exhaust pipe.


Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 1 NITROGEN OXIDES SENSOR

NG

7.REPAIR OR REPLACE EXHAUST PIPE
3.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P2A00 or P2A01 is output A
DTCs are not output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE EXHAUST PIPE
a.

Repair or replace the exhaust pipe.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
8.INSPECT EXHAUST PIPE
a.

Check for dirt, soot, clogging, leakage, or damage in the exhaust pipe.


Result:
Proceed to
OK
NG



OK

9.REPLACE NO. 2 NITROGEN OXIDES SENSOR

NG

10.REPAIR OR REPLACE EXHAUST PIPE
9.REPLACE NO. 2 NITROGEN OXIDES SENSOR
a.

Replace the No. 2 nitrogen oxides sensor.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
10.REPAIR OR REPLACE EXHAUST PIPE
a.

Repair or replace the exhaust pipe.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT