| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0106 | Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Range/Performance | DTC detection condition:
·
Engine speed is between 570 to 1200 rpm ·
Fuel injection rate is between 0 mm3/st to 35 mm3/st ·
Engine coolant temperature is 55°C (131°F) or less ·
EGR valve opening is 0% or less (EGR-cut status) ·
Exhaust brake is not actuated Malfunction Status: ·
Theoretical air quantity calculated from boost pressure and atmospheric pressure and actual air quantity are compared for at least 10 seconds, and the ratio of theoretical air quantity to actual air quantity is at least 1.15 or no greater than 0.75. ·
Difference between DCY value prior to above result and current DCY value is 0.10 or less ·
The condition "(Average boost pressure minus average atmospheric pressure) was 18 kPa or more" when the ignition switch off and engine was stopped after previous DCY is not continued for more than 3 seconds. Malfunction Duration: 1 cecond or more |
·
Harness or connector ·
Manifold absolute pressure sensor ·
ECM |
Class B1 | DTC stored |
The manifold absolute pressure sensor mounted on the diesel throttle outlet constantly measures the boost pressure.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P0106 | Idle the engine for 15 seconds. |
Refer to DTC P0108.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>P0107
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the connector connection for the manifold absolute pressure sensor connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the installation of the manifold absolute pressure sensor.
Make sure there is no dirt, damage or clogging in the sensing unit of the manifold absolute pressure sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the manifold absolute pressure sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M-51 - Body ground and other terminals | Always | 10 kΩ or higher |
| E-67 - Body ground and other terminals | Always | 10 kΩ or higher |
| E-77 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the manifold absolute pressure sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M-51 - E-67 | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the manifold absolute pressure sensor connector.
Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)
| *a | Signal Check Harness Lead Connector |
| *a | Signal Check Harness Lead Connector |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M-51 - B18-3 (VC) | Always | Below 1 Ω |
| E-67 - B18-2 (PIM) | Always | Below 1 Ω |
| M-77 - B18-1 (E) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
| *a | Front view of wire harness connector
(to Manifold Absolute Pressure Sensor) |
OK
NG
| *a | Front view of wire harness connector
(to Manifold Absolute Pressure Sensor) |
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B18-3 (VC) - B18-1 (E) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the manifold absolute pressure sensor.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>MANIFOLD ABSOLUTE PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
After starting the engine, warm it up until the engine coolant temperature is 80°C (176°F) or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC P0106 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Replace or replace the manifold absolute pressure sensor.
Clean the sensing unit and install it properly.
If damaged, replace the manifold absolute pressure sensor.
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the manifold absolute pressure sensor.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
After starting the engine, warm it up until the engine coolant temperature is 80°C (176°F) or more.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT