Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0097  Intake Air Temperature Sensor 2 Circuit Low Bank 1  P0098  Intake Air Temperature Sensor 2 Circuit High Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0097 Intake Air Temperature Sensor 2 Circuit Low Bank 1 Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.


Malfunction Status:

Intake air temperature sensor (for intake manifold side) output 0.06 V or less for at least 3 seconds.


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

Intake air temperature sensor (for intake manifold side)

·

ECM


Class B1 DTC stored
P0098 Intake Air Temperature Sensor 2 Circuit High Bank 1 Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.

·

Intake air temperature is in range of -7 to 35°C (19 to 95°F).

·

Intake air temperature sensor (built into mass air flow meter) is not in fault.


Malfunction Status:

Intake air temperature sensor (for intake manifold side) output remains less than 4.87 V (-35°C (-31°F)) for 3 seconds or more


Malfunction Duration:

3 seconds or more


·

Harness or connector

·

Intake air temperature sensor (for intake manifold side)

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

The intake air temperature sensor (for intake manifold side) installed on the intake manifold consistently measures intake manifold temperature.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0097
P0098
Ignition switch ON for 8 seconds or more.


WIRING DIAGRAM

A407162E20
1.948,0.75 2.104,0.948 0.156,0.198 10 false 2 1.938,1.333 2.094,1.531 0.156,0.198 10 false 1 0.656,2.094 1.385,2.292 0.729,0.198 10 false B13 0.646,2.302 3.031,2.677 2.385,0.375 10 false Intake Air Temperature Sensor (for Intake Manifold Side) 4.469,0.896 5.229,1.271 0.76,0.375 10 false E-63 4.469,1.479 5.229,1.854 0.76,0.375 10 false E-54 4.823,0.906 5.583,1.281 0.76,0.375 10 false B142 4.823,1.5 5.583,1.875 0.76,0.375 10 false B142 4.875,1.292 5.635,1.667 0.76,0.375 10 false 85 4.875,0.708 5.635,1.083 0.76,0.375 10 false 19 5.25,1.479 6.01,1.854 0.76,0.375 10 false E2 5.25,0.906 6.01,1.281 0.76,0.375 10 false THIA 5.625,2.417 6.385,2.792 0.76,0.375 10 false ECM 1.552,0.823 2.313,1.198 0.76,0.375 10 false THA 1.646,1.385 2.406,1.76 0.76,0.375 10 false E2

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the intake air temperature sensor (for intake manifold side) connector.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

13.CONNECT SECURELY
2.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Check the installation of the intake air temperature sensor (for intake manifold side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intake manifold side).


Result:
Proceed to
OK
NG



OK

3.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

12.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
3.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Inspect the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE) - ECM)

NG

11.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE) - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intake manifold side) connector.


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-63 - Body ground and other terminals Always 10 kΩ or higher
E-54 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK HARNESS AND CONNECTOR
A227773C15
0.385,1.073 0.833,1.375 0.448,0.302 1.01,1.781 1.573,1.229 true 2.375,1.75 2,1.24 true 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 0.5,1.146 0.813,1.344 0.313,0.198 10 false B13 0.813,1.771 1.271,1.969 0.458,0.198 10 false E2 2.375,1.792 2.833,1.99 0.458,0.198 10 false THA
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for intake manifold side))


A405887C12
1.5,0.115 1.875,0.385 0.375,0.271 0.26,0.208 0.573,0.406 0.313,0.198 10 false *a 1.635,0.167 1.792,0.365 0.156,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Disconnect the intake air temperature sensor (for intake manifold side) connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-63 - B13-2 (THA) Always Below 1 Ω
E-54 - B13-1 (E2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
A227773C15
0.385,1.073 0.833,1.375 0.448,0.302 1.01,1.781 1.573,1.229 true 2.375,1.75 2,1.24 true 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 0.5,1.146 0.813,1.344 0.313,0.198 10 false B13 0.813,1.771 1.271,1.969 0.458,0.198 10 false E2 2.375,1.792 2.833,1.99 0.458,0.198 10 false THA
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (for intake manifold side))


a.

Disconnect the intake air temperature sensor (for intake manifold side) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B13-2 (THA) - B13-1 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

8.REPLACE ECM
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0097 or P0098 is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
11.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Replace intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Replace or replace the intake air temperature sensor (for intake manifold side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intake manifold side).



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.CONNECT SECURELY
a.

Connect securely the intake air temperature sensor (for intake manifold side) connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END