Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0182  Fuel Temperature Sensor "A" Circuit Low  P0183  Fuel Temperature Sensor "A" Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0182 Fuel Temperature Sensor "A" Circuit Low Diagnosis Condition:
·

The conditions described above remain for 5 seconds or longer.

-

Ignition switch ON

-

Battery voltage is in the range of 10 V to 16 V

-

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.



Malfunction Status:

Output of the fuel temperature sensor remains at 0.1 V or less for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Fuel temperature sensor

·

Harness or connector

·

ECM


- DTC stored
P0183 Fuel Temperature Sensor "A" Circuit High Diagnosis Condition:
·

The conditions described above remain for 5 seconds or longer.

-

Ignition switch ON

-

Battery voltage is in the range of 10 V to 16 V

-

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.



Malfunction Status:

Output of the fuel temperature sensor remains at 4.85 V or greater for 3 seconds or longer.


Malfunction Duration:

3 seconds or more


·

Fuel temperature sensor

·

Harness or connector

·

ECM


- DTC stored

MONITOR DESCRIPTION

·

The fuel temperature sensor consistently measures fuel temperature.

·

The fuel temperature sensor is installed to the supply pump assembly.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0182
P0183
Ignition switch ON for 8 seconds or more.


WIRING DIAGRAM

A449918E03
0.417,2.125 2.531,2.375 2.115,0.25 10 false Fuel Temperature Sensor 0.406,1.917 0.646,2.094 0.24,0.177 10 false B8 2.021,0.844 2.26,1.021 0.24,0.177 10 false 2 2,1.427 2.24,1.604 0.24,0.177 10 false 1 5.25,0.948 5.646,1.104 0.396,0.156 10 false THF 5.24,1.521 5.479,1.698 0.24,0.177 10 false E2 4.823,0.938 5.177,1.094 0.354,0.156 10 false B142 4.823,1.521 5.177,1.688 0.354,0.167 10 false B142 4.938,0.76 5.177,0.938 0.24,0.177 10 false 8 4.469,0.948 4.823,1.125 0.354,0.177 10 false E-48 4.906,1.354 5.146,1.531 0.24,0.177 10 false 85 4.448,1.531 4.802,1.708 0.354,0.177 10 false M-54 5.677,2.396 6.385,2.635 0.708,0.24 10 false ECM 1.667,0.844 2.063,1 0.396,0.156 10 false THF 1.719,1.427 1.958,1.604 0.24,0.177 10 false E2

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration(Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

·

After replacing the suction control valve or fuel supply pump assembly, the ECM needs initialization(Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (FUEL TEMPERATURE SENSOR)
a.

Check the connector connection for the fuel temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.CHECK SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)

NG

13.CONNECT SECURELY
2.CHECK SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)
a.

Check the installation of the fuel temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the fuel temperature sensor.


Result:
Proceed to
OK
NG



OK

3.INSPECT SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)

NG

12.REPAIR OR REPLACE SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)
3.INSPECT SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)
a.

Inspect the fuel temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK FUEL TEMPERATURE SENSOR

NG

11.REPLACE SUPPLY PUMP ASSEMBLY
4.CHECK FUEL TEMPERATURE SENSOR
A256062C08
0.365,1.052 0.802,1.344 0.438,0.292 1.073,1.781 1.521,1.188 true 2.385,1.781 1.938,1.198 true 0.198,0.208 0.51,0.406 0.313,0.198 10 false *a 0.51,1.104 0.823,1.302 0.313,0.198 10 false B8 2.313,1.823 2.771,2.021 0.458,0.198 10 false THF 0.906,1.833 1.365,2.031 0.458,0.198 10 false E2
*a Front view of wire harness connector
(to Fuel Temperature Sensor)


a.

Disconnect the fuel temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B8-1 (E2) - B8-2 (THF) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

5.CHECK HARNESS OR CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
5.CHECK HARNESS OR CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Disconnect the fuel temperature sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-48 - Body ground and other terminals Always 10 kΩ or higher
M-54 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS OR CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK HARNESS OR CONNECTOR (FUEL TEMPERATURE SENSOR - ECM)
a.

Connect the fuel temperature sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A405887C07
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E48 - M-54 Always (20°C) 2.32 to 2.59 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0182 or P0183 is output A
DTCs are not output B




A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
11.REPLACE SUPPLY PUMP ASSEMBLY
a.

Replace the supply pump assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
12.REPAIR OR REPLACE SUPPLY PUMP ASSEMBLY (FUEL TEMPERATURE SENSOR)
a.

Repair or replace fuel temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the supply pump assembly.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
13.CONNECT SECURELY
a.

Connect securely the fuel temperature sensor.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

14.CHECK DTC OUTPUT
14.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END