Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0340  Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor  P0341  Camshaft Position Sensor "A" Circuit Range/Performance Bank 1 or Single Sensor  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor "A" Circuit Bank 1 or Single Sensor Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Engine speed of 0 rpm or more


Malfunction Status:

With the engine running at 600 rpm, the camshaft position sensor does not detect pulses for 1 second or longer.


Malfunction Duration:

1 seconds or more (engine speed is 600 rpm or higher)


·

Camshaft position sensor

·

Harness or connector

·

ECM


Class B1 DTC stored
P0341 Camshaft Position Sensor "A" Circuit Range/Performance Bank 1 or Single Sensor Diagnosis Condition:
·

Battery voltage is in the range of 10 V to 16 V

·

Engine speed of 450 rpm or more


Malfunction Status:

The number of the camshaft position sensor pulses per 2 engine revolutions is continuously abnormal (other than 5 pulses). (For example, 125 seconds for 600 rpm).


Malfunction Duration:

125 seconds or more (engine speed is 600 rpm or higher)


·

Camshaft position sensor

·

Harness or connector

·

ECM


Class C DTC stored

MONITOR DESCRIPTION

The camshaft position sensor consistently measures pulses from the camshaft position sensor.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0340 Start the engine and run it at idle for at least 1 second
P0341 Start the engine and run it at idle for at least 125 seconds


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P0340 is output A
DTC P0341 is output B




A

2.CHECK CONNECTOR CONNECTION CONDITION (CAMSHAFT POSITION SENSOR CONNECTOR)

B

12.CHECK CONNECTOR CONNECTION CONDITION (CAMSHAFT POSITION SENSOR CONNECTOR)
2.CHECK CONNECTOR CONNECTION CONDITION (CAMSHAFT POSITION SENSOR CONNECTOR)
a.

Check the connector connection for the camshaft position sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.CHECK CAMSHAFT POSITION SENSOR

NG

11.CONNECT SECURELY
3.CHECK CAMSHAFT POSITION SENSOR
a.

Check the installation of the camshaft position sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the camshaft position sensor.


Result:
Proceed to
OK
NG



OK

4.CHECK CAMSHAFT POSITION SENSOR

NG

10.REPAIR OR REPLACE CAMSHAFT POSITION SENSOR
4.CHECK CAMSHAFT POSITION SENSOR
A407242C12
0.51,0.979 0.917,1.25 0.406,0.271 1.292,1.667 1.677,1.25 true 2.135,1.677 1.938,1.25 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 2.094,1.708 2.406,1.906 0.313,0.198 10 false VG 0.635,1.042 0.948,1.24 0.313,0.198 10 false k2 1.177,1.677 1.49,1.875 0.313,0.198 10 false G-
*a Front view of wire harness connector
(to Camshaft Position Sensor)


a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Switch Condition Specified Condition
k2-3 (VG) - k2-2 (G-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK CAMSHAFT POSITION SENSOR

NG

9.CHECK HARNESS AND CONNECTOR
5.CHECK CAMSHAFT POSITION SENSOR
A407887E01
2.771,0.094 3.427,0.375 0.656,0.281 10 false 5 V/DIV. 3.052,1.01 3.427,1.323 0.375,0.313 10 false GND 1.188,1.927 2.292,2.146 1.104,0.219 10 false 20 ms/DIV.

A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


a.

Connect the camshaft position sensor connector.


b.

Connect the signal check harness to the ECM.


c.

Start the engine.


d.

Measure the signal voltage between the terminals and ECM.

Standard Voltage:
Tester Connection Condition Specified Condition
E-73 - E-54 Idling 0 to 5 V pulse waveform



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

6.CHECK CAMSHAFT POSITION SENSOR
6.CHECK CAMSHAFT POSITION SENSOR
a.

Connect the signal check harness to the ECM.


b.

Disconnect the camshaft position sensor connector.


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


A407242C13
0.51,0.979 0.917,1.25 0.406,0.271 1.063,1.646 1.479,1.229 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.656,1.052 0.969,1.25 0.313,0.198 10 false k2 0.854,1.688 1.167,1.885 0.313,0.198 10 false G1
*a Front view of wire harness connector
(to Camshaft Position Sensor)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-73 - k2-1 (G1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK DTC OUTPUT

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0340 is output A
DTCs are not output B




A

21.REPLACE ECM

B

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the camshaft position sensor connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Start the engine.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Condition Switch Condition Specified Condition
E-53 - E-54 Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

21.REPLACE ECM
10.REPAIR OR REPLACE CAMSHAFT POSITION SENSOR
a.

Repair or replace the camshaft position sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the camshaft position sensor.



Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
11.CONNECT SECURELY
a.

Connect securely the camshaft position sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
12.CHECK CONNECTOR CONNECTION CONDITION (CAMSHAFT POSITION SENSOR CONNECTOR)
a.

Check the connector connection for the camshaft position sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

13.CHECK CAMSHAFT POSITION SENSOR

NG

25.CONNECT SECURELY
13.CHECK CAMSHAFT POSITION SENSOR
a.

Check the installation of the camshaft position sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the camshaft position sensor.


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS OR CONNECTOR (CAMSHAFT PSITION SENSOR - ECM)

NG

24.REPAIR OR REPLACE CAMSHAFT POSITION SENSOR
14.CHECK HARNESS OR CONNECTOR (CAMSHAFT PSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-53 - Body ground and other terminals Always 10 kΩ or higher
E-54 - Body ground and other terminals Always 10 kΩ or higher
E-73 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS OR CONNECTOR (CAMSHAFT PSITION SENSOR - ECM)

NG

23.REPAIR OR REPLACE HARNESS OR CONNECTOR
15.CHECK HARNESS OR CONNECTOR (CAMSHAFT PSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-53 - k2-3 (VG) Always Below 1 Ω
E-54 - k2-2 (G-) Always Below 1 Ω
E-73 - k2-1 (G1) Always Below 1 Ω



Result:
Proceed to
OK
NG


A407242C14
0.51,0.979 0.917,1.25 0.406,0.271 1.219,1.792 1.5,1.25 true 1.719,1.76 1.719,1.25 true 2.302,1.792 1.938,1.26 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.656,1.042 0.969,1.24 0.313,0.198 10 false k2 1.042,1.802 1.354,2 0.313,0.198 10 false VG 1.667,1.802 1.979,2 0.313,0.198 10 false G- 2.271,1.802 2.583,2 0.313,0.198 10 false G1
*a Front view of wire harness connector
(to Camshaft Position Sensor)



OK

16.CHECK CAMSHAFT POSITION SENSOR

NG

22.REPAIR OR REPLACE HARNESS OR CONNECTOR
16.CHECK CAMSHAFT POSITION SENSOR
A407242C15
0.51,0.979 0.917,1.25 0.406,0.271 1.271,1.75 1.677,1.271 true 2.333,1.74 1.958,1.26 true 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.635,1.042 0.948,1.24 0.313,0.198 10 false k2 1.094,1.76 1.406,1.958 0.313,0.198 10 false G- 2.344,1.781 2.656,1.979 0.313,0.198 10 false VG
*a Front view of wire harness connector
(to Camshaft Position Sensor)


a.

Disconnect the camshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
k2-3 (VG) - k2-2 (G-) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

17.CHECK CAMSHAFT POSITION SENSOR

NG

21.REPLACE ECM
17.CHECK CAMSHAFT POSITION SENSOR
A407889E03
0.479,1.063 0.938,1.26 0.458,0.198 10 false G 0.406,1.75 1.396,2.198 0.99,0.448 10 false NE 3.167,2.469 4.219,2.688 1.052,0.219 10 false 20 ms/DIV. 3.458,0.052 4.51,0.271 1.052,0.219 10 false 720° 6.427,0.135 7.021,0.427 0.594,0.292 10 false 5 V/DIV. 6.625,1.135 7.156,1.438 0.531,0.302 10 false GND 6.625,1.771 7.156,2.073 0.531,0.302 10 false GND

A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


a.

Connect the camshaft position sensor connector.


b.

Connect the signal check harness to the ECM and ECM vehicle side harness.


c.

Start the engine.


d.

Measure the signal voltage between the terminals and ECM.

Standard Voltage:
Tester Connection Condition Specified Condition
E-54 - E-73 Idling 5 pulses for every 2 revolutions of engine



Result:
Proceed to
OK
NG



OK

18.CHECK DTC OUTPUT

NG

20.REPAIR OR REPLACE CAMSHAFT POSITION SENSOR
18.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0341 is output A
DTCs are not output B




A

19.REPLACE ECM

B

END

19.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
20.REPAIR OR REPLACE CAMSHAFT POSITION SENSOR
a.

Repair or replace the camshaft position sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the camshaft position sensor.



Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
21.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
22.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
23.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
24.REPAIR OR REPLACE CAMSHAFT POSITION SENSOR
a.

Repair or replace the camshaft position sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the camshaft position sensor.



Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
25.CONNECT SECURELY
a.

Connect securely the camshaft position sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

26.CHECK DTC OUTPUT
26.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END