Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0628  Fuel Pump "A" Control Circuit Low  P0629  Fuel Pump "A" Control Circuit High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0628 Fuel Pump "A" Control Circuit Low Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.

·

The injectors and injector driver circuits have started running.


Malfunction Status:

Suction control valve drive current remains less than 350 mA for 2.1 seconds.


Malfunction Duration:

2.1 seconds or more


·

Suction control valve

·

Harness or connector

·

ECM


Class A DTC stored
P0629 Fuel Pump "A" Control Circuit High Diagnosis Condition:
·

Ignition switch ON

·

Battery voltage is in the range of 10 V to 16 V

·

The engine is stopped, or the engine speed remains at 500 rpm or more for 5 seconds or more.

·

The injectors and injector driver circuits have started running.


Malfunction Status:

Suction control valve drive current remains higher than 1300 mA for 2.1 seconds.


Malfunction Duration:

2.1 seconds or more


·

Suction control valve

·

Harness or connector

·

ECM


Class A DTC stored

MONITOR DESCRIPTION

The supply pump controls a fuel delivery rate to control common rail pressure.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0628
P0629
Ignition switch ON for 8 seconds or more.


WIRING DIAGRAM

A407171E02
0.479,2.135 2.625,2.333 2.146,0.198 10 false Suction Control Valve 0.49,1.958 0.875,2.188 0.385,0.229 10 false B52 2.042,0.729 2.354,0.927 0.313,0.198 10 false 1 2.042,1.344 2.354,1.542 0.313,0.198 10 false 2 5.26,0.854 5.75,1.094 0.49,0.24 10 false PCV+ 5.25,1.438 5.729,1.635 0.479,0.198 10 false PCV- 4.813,0.844 5.302,1.083 0.49,0.24 10 false B142 4.813,1.417 5.302,1.656 0.49,0.24 10 false B142 4.896,1.26 5.385,1.5 0.49,0.24 10 false 72 4.906,0.656 5.396,0.896 0.49,0.24 10 false 94 4.5,0.833 4.99,1.073 0.49,0.24 10 false E-9 4.458,1.417 4.948,1.656 0.49,0.24 10 false E-10 5.656,2.333 6.417,2.563 0.76,0.229 10 false ECM 1.573,0.729 2.063,0.969 0.49,0.24 10 false SCV+ 1.604,1.344 2.094,1.583 0.49,0.24 10 false SCV-

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the suction control valve or injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the suction control valve connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

2.INSPECT SUCTION CONTROL VALVE

NG

10.CONNECT SECURELY
2.INSPECT SUCTION CONTROL VALVE
a.

Inspect the suction control valve.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL SUPPLY PUMP>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

9.REPLACE SUCTION CONTROL VALVE
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A407245C05
0.74,1 1.229,1.271 0.49,0.271 1.375,1.594 1.635,1.177 true 2.26,1.615 1.865,1.188 true 0.115,0.135 0.427,0.333 0.313,0.198 10 false *a 1.177,1.615 1.917,1.813 0.74,0.198 10 false SCV+ 0.885,1.052 1.198,1.25 0.313,0.198 10 false B52 2.156,1.615 2.896,1.813 0.74,0.198 10 false SCV-
*a Front view of wire harness connector
(to Suction Control Valve)


a.

Disconnect the ECM connector.


b.

Disconnect the suction control valve connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B52-1 (SCV+) - Body ground and other terminals Always 10 kΩ or higher
B52-2 (SCV-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
A405886C09
1.51,0.125 1.885,0.406 0.375,0.281 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 1.667,0.208 1.979,0.406 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


a.

Disconnect the ECM connector.


b.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-9 - E-10 20°C 7.65 to 8.15 kΩ



Result:
Proceed to
OK
NG



OK

5.CHECK DTC OUTPUT

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0628 and P0629 are output A
DTCs are not output B




A

6.REPLACE ECM

B

END

6.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



e.

Turn the ignition switch off for 30 seconds or more.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
9.REPLACE SUCTION CONTROL VALVE
a.

Replace the suction control valve.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>SUCTION CONTROL VALVE>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
10.CONNECT SECURELY
a.

Connect securely the suction control valve connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT