Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P2428  Exhaust Gas Temperature Too High Bank 1  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2428 Exhaust Gas Temperature Too High Bank 1 Diagnosis Condition:

While the engine is in operation.


Malfunction Status:
·

Valve of the No. 1 exhaust gas temperature sensor more than 800°C (1472°F)

·

Malfunction determination time: Immediately.


Malfunction Duration:

30 seconds or more


·

No. 1 exhaust gas temperature sensor

·

ECM


Class B2 DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P2428 PM forced regeneration

CAUTION / NOTICE / HINT

NOTICE:

After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is output, after checking and repairing, check the engine oil amount.

·

Replace the engine oil if it exceeds the upper level of the level gauge (X mark: 25 mm over the upper level of a standard level gauge).



PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2428 is output A
DTC P2428 and other DTCs are output B




A

2.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)

B

2.CHECK READ VALUE USING GTS (INJECTION VOLUME, ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


e.

Read the value displayed on the GTS.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTOR CONNECTION CONDITION

NG

21.REPLACE INJECTOR ASSEMBLY
3.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the No. 1 exhaust gas temperature sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

4.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

20.CONNECT SECURELY
4.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Check the installation of the No. 1 exhaust gas temperature sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of No. 1 exhaust gas temperature sensor.


Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

19.REPAIR OR REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
5.INSPECT NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Inspect the No. 1 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR

NG

18.REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
6.CHECK NO. 1 EXHAUST GAS TEMPERATURE SENSOR
A450001C04
0.604,0.948 1.021,1.25 0.417,0.302 1.125,1.76 1.552,1.229 true 2.323,1.75 1.885,1.229 true 0.104,0.125 0.417,0.323 0.313,0.198 10 false *a 0.656,1.031 1.167,1.208 0.51,0.177 10 false B141 0.896,1.781 1.406,1.958 0.51,0.177 10 false TOIL 2.271,1.781 2.781,1.958 0.51,0.177 10 false GND
*a Front view of wire harness connector
(to No. 1 Exhaust Gas Temperature Sensor)


a.

Disconnect the No. 1 exhaust gas temperature sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B141-1 (TOIL) - B141-2 (GND) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

9.CHECK OIL LEAK

NG

7.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)
7.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the No. 1 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-50 - Body ground and other terminals Always 10 kΩ or higher
E-77 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)

NG

17.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS OR CONNECTOR (NO. 1 EXHAUST GAS TEMPERATURE SENSOR - ECM)
a.

Turn the ignition switch off.


b.

Connect the No. 1 exhaust gas temperature sensor connector.


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.
A405887C17
1.521,0.167 1.885,0.448 0.365,0.281 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.667,0.25 1.865,0.427 0.198,0.177 10 false M
*a Signal Check Harness Lead Connector


A405887C14
1.5,0.083 1.948,0.385 0.448,0.302 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.667,0.156 1.979,0.354 0.313,0.198 10 false E
*a Signal Check Harness Lead Connector


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M-50 - E-77 Always (20°C) 13.7 to 29.8 kΩ
M-50 - E-77 Always (50°C) 7.13 to 13.7 kΩ
M-50 - E-77 Always (80°C) 4.1 to 7.13 kΩ



Result:
Proceed to
OK
NG



OK

9.CHECK OIL LEAK

NG

16.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK OIL LEAK
a.

Disconnect the intake pipe, hoses.


b.

Check if there are oil stuck within pipe, hose.


Result:
Proceed to
OK
NG



OK

10.CHECK FRONT EXHAUST PIPE ASSEMBLY

NG

15.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
10.CHECK FRONT EXHAUST PIPE ASSEMBLY
a.

Remove the front exhaust pipe assembly, and then check it for soot and ATC damage.


Result:
Proceed to
OK
NG



OK

11.PERFORM PM FORCED REGENERATION

NG

14.REPAIR OR REPLACE FRONT EXHAUST PIPE ASSEMBLY
11.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Result Proceed to
Manual forced regeneration completed normally A
Manual forced regeneration does not complete normally B



A

12.CHECK DTC OUTPUT

B

13.CHECK DTC OUTPUT
12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Perform the inspection procedure for the output DTCs.


Result:
Proceed to
NEXT



NEXT

14.REPAIR OR REPLACE FRONT EXHAUST PIPE ASSEMBLY
a.

Repair or replace the front exhaust pipe assembly.

Click hereEngine / Hybrid System>N04C-WA (EXHAUST)>EXHAUST PIPE>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
15.REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
a.

Repair or replace malfunctioning parts, component and area.


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
16.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
17.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
18.REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Replace the No. 1 exhaust gas temperature sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>EXHAUST GAS TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
19.REPAIR OR REPLACE NO. 1 EXHAUST GAS TEMPERATURE SENSOR
a.

Repair or replace the No. 1 exhaust gas temperature sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the No. 1 exhaust gas temperature sensor.



Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
20.CONNECT SECURELY
a.

Connect securely the No. 1 exhaust gas temperature sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

12.CHECK DTC OUTPUT
21.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

12.CHECK DTC OUTPUT