| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| U029D | Lost Communication with NOx Sensor "A" | Diagnosis Condition:
·
Ignition switch ON ·
ECM power supply voltage is in the range of 10 V to 16 V Malfunction Status: Disconnection between No. 1 nitrogen oxides sensor and CAN bus line is detected for 3 seconds Malfunction Duration: 3 seconds or more |
·
No. 1 nitrogen oxides sensor ·
Harness or connector ·
ECM |
Class C | DTC stored |
| U029E | Lost Communication with NOx Sensor "B" | Diagnosis Condition:
·
Ignition switch ON ·
ECM power supply voltage is in the range of 10 V to 16 V Malfunction Status: Disconnection between No. 2 nitrogen oxides sensor and CAN bus line is detected for 3 seconds Malfunction Duration: 3 seconds or more |
·
No. 2 nitrogen oxides sensor ·
Harness or connector ·
ECM |
Class C | DTC stored |
U029D:
The No. 1 nitrogen oxides sensor is responsible for the CAN communication with the DCU (emission control ECU assembly).
U029E:
No. 2 nitrogen oxides sensor is connected via the DCU (emission control ECU assembly) and CAN communication.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| U029D
U029E |
Ignition switch ON for 3 seconds or more |
After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
According to the display on the GTS, select "Health Check".
Check for currently output system DTCs.
| Result | Proceed to |
|---|---|
| DTC U029D is output | A |
| DTC U029E is output | B |
| 2 or more of the following DTCs are simultaneously output: U0073, U010A, U010C, U010E, U029D, U029E, U02A2 and U02A3 and urea system DTCs U010031 and U02A231 | C |
| DTCs are not output | D |
A
B
C
D
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
Check the connector connection for the No. 1 nitrogen oxides sensor connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor) |
Disconnect the No. 1 nitrogen oxides sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A116-5 (VCC) - A116-1 (GND) | Ignition switch ON | 11 to 14 V |
| A116-5 (VCC) - A116-4 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 1 nitrogen oxides sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A116-2 (CANH) - A116-3 (CANL) | Ignition switch off | 54 to 69 Ω |
| Positive (+) battery terminal - A116-2 (CANH) | Ignition switch off | 6 kΩ or higher |
| Positive (+) battery terminal - A116-3 (CANL) | ||
| A116-2 (CANH) - Body ground | Ignition switch off | 200 Ω or higher |
| A116-3 (CANL) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace No. 1 nitrogen oxides sensor.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read Current DTCs.
| Result | Proceed to |
|---|---|
| DTC U029D or U029E is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the No. 1 nitrogen oxides sensor connector.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT
Check the connector connection for the No. 2 nitrogen oxides sensor connector.
The connector is connected securely and there are no contact pressure problems.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor) |
Disconnect the No. 2 nitrogen oxides sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-5 (VCC) - P14-4 (GND) | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor) |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 2 nitrogen oxides sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| P14-2 (CANH) - P14-3 (CANL) | Ignition switch off | 54 to 69 Ω |
| Positive (+) battery terminal - P14-2 (CANH) | Ignition switch off | 6 kΩ or higher |
| Positive (+) battery terminal - P14-3 (CANL) | ||
| P14-2 (CANH) - Body ground | Ignition switch off | 200 Ω or higher |
| P14-3 (CANL) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace No. 2 nitrogen oxides sensor.
Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect securely the No. 2 nitrogen oxides sensor connector.
Repair it as needed.
| Proceed to |
|---|
| NEXT |
NEXT