Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0148  Fuel Delivery Error  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0148 Fuel Delivery Error Diagnosis Condition:
·

The vehicle speed is 0 km/h

·

A change in the engine revolution is 938 r/min/sec or less.

·

A change in the fuel injection quantity is 312 mm3/st/sec or less.

·

A change in the fuel pressure is 93.7 MPa/sec or less.

·

The target operating current of the supply pump is not less than 1500 mA but not more than 1800 mA.


Malfunction Status:

A change in the operating current of the supply pump upon post injection falls below the specified value.


Malfunction Duration:

10 seconds or more


·

Fuel injection pipe

·

Engine assembly

·

Common rail assembly

·

Injector assembly


Class C DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0148 After starting the engine, warm it up until the engine coolant temperature is 80°C or more.


CAUTION / NOTICE / HINT

NOTICE:

After replacing the injector assembly, the ECM needs registration (Click here Engine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

After starting the engine, warm it up until the engine coolant temperature is 80°C or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0148 is output A
DTCs are not output B




A

2.CHECK FUEL LINE

B

12.CHECK INJECTOR CLAMP
2.CHECK FUEL LINE
a.

Check that the fuel line has no leaks or clogging.

HINT:
·

Entry of foreign matter into the fuel tank.

·

Fuel hose breakage, collapsing, looseness.

·

High-pressure pipe breakage, collapsing, looseness.




Result:
Proceed to
OK
NG



OK

3.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY

NG

11.REPAIR OR REPLACE TROUBLE AREAS
3.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Check that the fuel filter element sub-assembly is not dirty or clogged or damaged.


Result:
Proceed to
OK
NG



OK

4.CHECK DTC OUTPUT

NG

10.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

After starting the engine, warm it up until the engine coolant temperature is 80°C or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0148 is output A
DTCs are not output B




A

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER FUEL CUT)

B

END

5.PERFORM ACTIVE TEST USING GTS (CONTROL THE CYLINDER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and GTS on.


c.

After starting the engine, warm it up until the engine coolant temperature is 80°C or more.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder Fuel Cut #1 to #4


e.

Maintain the engine speed at 1500 rpm and remember the engine sound before the Active Test is performed.


f.

While maintaining the engine speed, perform the Active Tests from #1 to #4 and check if the engine sound changes.


Result:
Result Proceed to
When comparing cylinders #1 to #4, there is a cylinder where the engine sound clearly changes. A
When comparing cylinders #1 to #4, there are no cylinders where the engine sound clearly changes. B



A

6.REPLACE INJECTOR ASSEMBLY

B

8.REPLACE COMMON RAIL ASSEMBLY
6.REPLACE INJECTOR ASSEMBLY
a.

Replace the defective injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

After starting the engine, warm it up until the engine coolant temperature is 80°C or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0148 is output A
DTCs are not output B




A

8.REPLACE COMMON RAIL ASSEMBLY

B

END

8.REPLACE COMMON RAIL ASSEMBLY
a.

Replace common rail assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>COMMON RAIL>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

After starting the engine, warm it up until the engine coolant temperature is 80°C or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0148 is output A
DTCs are not output B




A

12.CHECK INJECTOR CLAMP

B

END

10.REPLACE FUEL FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the fuel filter element sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL FILTER (for Fuel Tank Side)>REPLACEMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
11.REPAIR OR REPLACE TROUBLE AREAS
a.

Repair or replace the faulty part.


Result:
Proceed to
NEXT



NEXT

3.CHECK FUEL FILTER ELEMENT SUB-ASSEMBLY
12.CHECK INJECTOR CLAMP
a.

Check that the injector clamp is not loose.


b.

Check that there is no "insufficient engagement" of the injector clamp claw.


Result:
Proceed to
OK
NG



OK

13.INSPECT VALVE CLEARANCE

NG

REPAIR OR REPLACE TROUBLE AREAS

13.INSPECT VALVE CLEARANCE
a.

Inspect the valve clearance.


Result:
Proceed to
OK
NG



OK

14.INSPECT ENGINE COMPRESSION PRESSURE

NG

ADJUST VALVE CLEARANCE

14.INSPECT ENGINE COMPRESSION PRESSURE
a.

Check the engine compression pressure.


Result:
Proceed to
OK
NG



OK

15.CHECK CRANKSHAFT POSITION SENSOR

NG

ENGINE OVERHAUL

15.CHECK CRANKSHAFT POSITION SENSOR
a.

Inspect the condition of crankshaft position sensor connector (looseness or poor contact).


b.

Check the installation of the crankshaft position sensor.


Result:
Proceed to
OK
NG



OK

16.CHECK DTC OUTPUT

NG

REPAIR OR REPLACE TROUBLE AREAS

16.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

After starting the engine, warm it up until the engine coolant temperature is 80°C or more.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read Current DTCs.

Result:
Result Proceed to
DTC P0148 is output A
DTCs are not output B




A

INSPECT CRANKSHAFT CONNECTING RODS, FLYWHEEL, AND OTHER PARTS OF THE DRIVE SYSTEM

B

END