Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0402  EGR "A" Flow Excessive Detected  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0402 EGR "A" Flow Excessive Detected Diagnosis Condition:
·

Ignition switch ON

·

DPR auto-regeneration is inactive

·

Engine coolant temperature is 55°C (131°F) or more.

·

Engine speed of 500 to 2000 rpm.

·

Fuel injection rate 0 to 100 mm3/st

·

Exhaust brake is not actuated.


Malfunction Status:
·

When EGR feedback (value of theoretical EGR rate - actual EGR rate) stays above 20% for at least 13 seconds.

·

Above criterion is determined from the boost pressure, intake manifold temperature, air intake quantity, fuel injection rate, and engine speed.


Malfunction Duration:

13 seconds or more


·

Intake air temperature sensor (for intake manifold side) failure

·

Mass air flow meter failure

·

Manifold absolute pressure sensor failure

·

Injector failure

·

EGR valve failure

·

Clogged intake system

·

VNT control failure


Class B1 DTC stored

MONITOR DESCRIPTION

·

EGR valve is a butterfly type.

·

EGR valve opening is controlled by engine speed and amount of intake air.

·

EGR valve opening is adjusted by engine ECU and CAN communication.

·

EGR valve will not operate when coolant temperature is low (40°C (104°F or less).

·

ECM calculates the actual EGR rate based on information from the manifold absolute pressure sensor, crankshaft position sensor, intake air temperature sensor (for intake manifold side), and mass air flow meter.

·

ECM compares the actual EGR rate and the theoretical EGR rate stored in the ECM memory.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0402 30 seconds or more with the engine speed from 1400 to 2300 rpm


CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR VALVE POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Valve Position / Data List / Actual EGR Valve Position and Target EGR Valve Position


d.

Check each step from 90 to 0% of the time lag of the target EGR valve opening and actual EGR valve opening.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 5 seconds.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)

NG

27.REPLACE EGR VALVE ASSEMBLY
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE VN TURBO POSITION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the VN Turbo Position / Data List / Target VN Turbo Position and Actual VN Turbo Position.


d.

Check each step from 90 to 0% of the time lag of the target VN turbo position and actual VN turbo position.

NOTICE:

Perform the inspection while the engine is stopped to avoid engine damages.


Standard:

The response delay should be less than 3 seconds.



Result:
Proceed to
OK
NG



OK

3.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

26.REPLACE TURBOCHARGER SUB-ASSEMBLY
3.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Check the air cleaner element for dirt, clogging, or damage.


b.

Make sure the element is a genuine part.


Result:
Proceed to
OK
NG



OK

4.CHECK MASS AIR FLOW METER

NG

25.CLEAN OR REPLACE AIR CLEANER ELEMENT SUB-ASSEMBLY
4.CHECK MASS AIR FLOW METER
a.

Check the installation of the mass air flow meter.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the mass air flow meter.


Result:
Proceed to
OK
NG



OK

5.CHECK CONNECTOR CONNECTION CONDITION

NG

24.REPAIR OR REPLACE MASS AIR FLOW METER
5.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the mass air flow meter connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

6.CHECK AIR INTAKE SYSTEM

NG

23.CONNECT SECURELY
6.CHECK AIR INTAKE SYSTEM
a.

Check the air intake system (between mass air flow meter and diesel throttle body) for dirt, clogging, or damage.


Result:
Proceed to
OK
NG



OK

7.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

22.CLEAN OR REPLACE PARTS AS NEEDED
7.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Check the installation of the manifold absolute pressure sensor.


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the manifold absolute pressure sensor.


Result:
Proceed to
OK
NG



OK

8.CHECK CONNECTOR CONNECTION CONDITION

NG

21.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
8.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the intake air temperature sensor (for intake manifold side) connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

9.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

20.CONNECT SECURELY
9.CHECK INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Check the installation of the intake air temperature sensor (for intake manifold side).


b.

Make sure there is no dirt, damage or clogging in the sensing unit of the intake air temperature sensor (for intake manifold side).


Result:
Proceed to
OK
NG



OK

10.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)

NG

19.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
10.INSPECT INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Inspect the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK EGR VALVE ASSEMBLY

NG

18.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
11.CHECK EGR VALVE ASSEMBLY
a.

Check the EGR valve for damage due to foreign substances.


b.

Check if there is soot obstructing the exhaust gas passageway inlet or outlet.


Result:
Proceed to
OK
NG



OK

12.CHECK READ VALUE USING GTS (INJECTION VOLUME AND ENGINE SPEED)

NG

17.CLEAN PASSAGEWAY
12.CHECK READ VALUE USING GTS (INJECTION VOLUME AND ENGINE SPEED)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed and Injection Volume


d.

Read the value.


Standard:
Item Condition Reference Value
Engine Speed
·

Engine speed: 1500 rpm

·

Engine coolant temperature: 80°C or higher

·

Shift position N

·

A/C OFF

·

Air compressor OFF


Speed fluctuation amount is 15 rpm or less
Injection Volume 5 mm3/st or more


Result:
Proceed to
OK
NG



OK

13.CHECK DTC OUTPUT

NG

16.REPLACE INJECTOR ASSEMBLY
13.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Read Current DTCs.

Result:
Result Proceed to
DTC P0402 is output A
DTCs are not output B




A

14.REPLACE ECM

B

END

14.REPLACE ECM
a.

Replace the ECM.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
15.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.



d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.


f.

Perform the confirmation driving pattern.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.


i.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

16.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL INJECTOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
17.CLEAN PASSAGEWAY
a.

Remove foreign substances and clean the passageway.

HINT:

Replace the EGR valve if it is damaged.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
18.REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Replace the intake air temperature sensor (for intake manifold side).

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>INTAKE AIR TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
19.REPAIR OR REPLACE INTAKE AIR TEMPERATURE SENSOR (FOR INTAKE MANIFOLD SIDE)
a.

Repair or replace the intake air temperature sensor (for intake manifold side).

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the intake air temperature sensor (for intake manifold side).



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
20.CONNECT SECURELY
a.

Connect securely the intake air temperature sensor (for intake manifold side) connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
21.REPAIR OR REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Repair or replace the manifold absolute pressure sensor.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the manifold absolute pressure sensor.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
22.CLEAN OR REPLACE PARTS AS NEEDED
a.

Clean or replace parts as needed.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
23.CONNECT SECURELY
a.

Connect securely the mass air flow meter connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
24.REPAIR OR REPLACE MASS AIR FLOW METER
a.

Repair or replace the mass air flow meter.

HINT:

Clean the sensing unit and install it properly.

If damaged, replace the mass air flow meter.



Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
25.CLEAN OR REPLACE AIR CLEANER ELEMENT SUB-ASSEMBLY
a.

Clean or replace the air cleaner filter element sub-assembly.


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
26.REPLACE TURBOCHARGER SUB-ASSEMBLY
a.

Replace the turbocharger sub-assembly.

Click hereEngine / Hybrid System>N04C-WA (INTAKE)>TURBOCHARGER>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT
27.REPLACE EGR VALVE ASSEMBLY
a.

Result:
Proceed to
NEXT



NEXT

15.CHECK DTC OUTPUT