Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P0500  Vehicle Speed Sensor "A"  P0501  Vehicle Speed Sensor "A" Range/Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" Diagnosis Condition:
·

Ignition switch ON


·

The conditions described below remain for 5 seconds or longer.

-

Engine speed is 1200 rpm or more.

-

Gear position: other than neutral.

-

The fuel injection quantity is 60 mm3/st or more.

-

Engine coolant temperature is 50°C (122°F) or higher.

-

Battery voltage is in the range of 10 V to 16 V

-

PTO is not actuated.



Malfunction Status:

Output of the vehicle speed sensor remains at a vehicle speed of 0 km/h (0 mile) for 5 seconds or longer.


Malfunction Duration:

5 seconds or more


·

Combination meter assembly

·

Harness or connector

·

ECM


Class B1 DTC stored
P0501 Vehicle Speed Sensor "A" Range/Performance Diagnosis Condition:
·

Ignition switch ON

·

Engine speed is 500 rpm or more.

·

The fuel injection quantity is 0 mm3/st or less.

·

Battery voltage is in the range of 10 V to 16 V


Malfunction Status:

Vehicle speed pulse frequency remains at 200 km/h (124 mile) for 5 seconds or longer.


Malfunction Duration:

5 seconds or more


·

Combination meter assembly

·

Harness or connector

·

ECM


Class B1 DTC stored

MONITOR DESCRIPTION

P0500
·

The ECM consistently measures pulses from the vehicle speed sensor through combination meter assembly.


P0501
·

The ECM consistently measures pulses from the vehicle speed sensor.


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0500
P0501
After warming up the engine, idle the engine for 5 seconds or more, and then drive at an engine speed of 1200 rpm or higher.

WIRING DIAGRAM

A407168E07
1.979,1.135 2.594,1.333 0.615,0.198 10 false +S 2.271,0.969 2.885,1.167 0.615,0.198 10 false 6 4.865,0.875 5.479,1.073 0.615,0.198 10 false 58 4.813,1.125 5.427,1.323 0.615,0.198 10 false A115 4.344,1.115 4.958,1.313 0.615,0.198 10 false V-14 5.26,1.115 5.875,1.313 0.615,0.198 10 false SP1 5.677,1.938 6.292,2.135 0.615,0.198 10 false ECM 0.896,1.771 1.51,1.969 0.615,0.198 10 false J1 0.906,1.958 3.198,2.281 2.292,0.323 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY
a.

Drive the vehicle and confirm that the combination meter (speedometer) is working properly.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

NG

9.CHECK COMBINATION METER ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Turn the ignition switch off.


b.

Disconnect the combination meter assembly connector.


A405886C10
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-14 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (CHECK FOR OPEN IN WIRE HARNESS)
a.

Turn the ignition switch off.


b.

Disconnect the combination meter assembly connector.


A405886C10
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


c.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V-14 - J1-6 (+S) Always Below 1 Ω



Result:
Proceed to
OK
NG


A241244C08
1.5,0.333 1.833,0.583 0.333,0.25 0.979,1.813 1.135,1.229 true 0.094,0.083 0.333,0.271 0.24,0.188 10 false *a 0.896,1.844 1.51,2.042 0.615,0.198 10 false +S 1.583,0.385 1.813,0.552 0.229,0.167 10 false J1
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

4.CHECK COMBINATION METER ASSEMBLY

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.CHECK COMBINATION METER ASSEMBLY
a.

Connect the signal check harness to the ECM vehicle side harness. (Do not connect harness to the ECM)


b.
A405886C10
1.479,0.125 1.896,0.396 0.417,0.271 0.177,0.167 0.49,0.365 0.313,0.198 10 false *a 1.635,0.188 1.948,0.385 0.313,0.198 10 false V
*a Signal Check Harness Lead Connector


Check the voltage between the terminal of the combination meter assembly and the body ground.

Standard Voltage:
Tester Connection Condition Specified Condition
V-14 - Body ground Driving at approximately 20 km/h Voltage generated intermittently



Result:
Proceed to
OK
NG


A317714E04
3.042,1.25 3.365,1.406 0.323,0.156 10 false GND 1.167,1.969 2.625,2.156 1.458,0.188 10 false 10 msec./DIV. 2.844,0.24 3.385,0.521 0.542,0.281 10 false 5 V/DIV.


OK

5.REPLACE ECM

NG

6.REPLACE COMBINATION METER ASSEMBLY
5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
6.REPLACE COMBINATION METER ASSEMBLY
a.

Replace the combination meter assembly.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
9.CHECK COMBINATION METER ASSEMBLY
a.

Check the combination meter (vehicle speed signal system).


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC OUTPUT
10.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off for 30 seconds or more.


e.

Perform the confirmation driving pattern.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END