Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P20D8  Exhaust Aftertreatment Fuel Supply Control Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20D8 Exhaust Aftertreatment Fuel Supply Control Performance Diagnosis Condition:
·

P20DE diagnosis has completed.

·

P0005 diagnosis has completed.

·

DPR regeneration is in process, or the following conditions remain for 3 seconds.

- Engine revolution: 1000 rpm or more

- No. 3 exhaust gas temperature sensor: 260°C (500°F) or more

- No. 4 exhaust gas temperature sensor: 200°C (392°F) or more

·

Number of times of exhaust fuel addition injector assembly (indicated times of engine ECU): 10 times


Malfunction Status:

The number of times of actual exhaust fuel addition injector assembly falls below 30% against the indication of exhaust fuel addition injector assembly.


Malfunction Duration:

3 seconds or more


·

Fuel pipe

·

Exhaust fuel addition injector assembly


Class B1 DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20D8 PM forced regeneration

CAUTION / NOTICE / HINT

NOTICE:

After replacing the injector assembly, the ECM needs registration.(Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
DTC P20D8 is output A
DTCs other than P20D8 are output B




A

2.INSPECT FUEL PIPE SUB-ASSEMBLY

B

2.INSPECT FUEL PIPE SUB-ASSEMBLY
a.

Check if any of the following defects is found in the pipe between the fuel pump and the exhaust fuel addition injector assembly.

·

Fuel leakage (loose joint bolt)

·

Crush

·

Wrong assembly



Result:
Proceed to
OK
NG



OK

3.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

NG

4.REPAIR OR REPLACE DEFECTIVE PART
3.INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
a.

Remove the exhaust fuel addition injector assembly and clean the injection hole.


b.

Install the exhaust fuel addition injector assembly and inspect operation of the exhaust fuel addition injector assembly by using the GTS.


Result:
Proceed to
NEXT



NEXT

6.PERFORM PM FORCED REGENERATION
4.REPAIR OR REPLACE DEFECTIVE PART
a.

Repair or replace the defective part.


Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FUEL SYSTEM
5.BLEED AIR FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

6.PERFORM PM FORCED REGENERATION
6.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P20D8 is output A
DTCs are not output B




B

END

A

REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY