Home › Engine / Hybrid System › N04C-WA (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _082611 N04C-WA ENGINE CONTROL _0399963 ECD SYSTEM C

N04C-WA ENGINE CONTROL  ECD SYSTEM  P20DE  Exhaust Aftertreatment Fuel Pressure Sensor Circuit Range/Performance  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P20DE Exhaust Aftertreatment Fuel Pressure Sensor Circuit Range/Performance Diagnosis Condition:
·

The engine revolution is in the range of 1500 to 3000 rpm.

·

Engine speed fluctuation is 156 rpm or less.

·

The difference between the target fuel pressure and the actual fuel pressure is 7.8 MPa or less.


Malfunction Status:

Fuel pressure in the fuel piping (for aftertreatment): The difference between the predicted fuel pressure and the actual fuel pressure remains at 0.5 MPa or more for 20 seconds.


Malfunction Duration:

20 seconds or more


·

Crankshaft position sensor

·

Fuel pump

·

Fuel pipe


Class B1 DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P20DE PM forced regeneration


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Turn the ignition switch to ON and turn the ignition switch off and wait for 5 seconds or more.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Read the DTCs.

Result:
Result Proceed to
DTC P20DE is output A
DTCs other than P20DE are output B




A

2.CHECK CONNECTOR CONNECTION CONDITION

B

2.CHECK CONNECTOR CONNECTION CONDITION
a.

Check the connector connection for the No. 2 fuel pressure sensor connector.

Standard:

The connector is connected securely and there are no contact pressure problems.



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL PIPE SUB-ASSEMBLY

NG

9.CONNECT SECURELY
3.INSPECT FUEL PIPE SUB-ASSEMBLY
a.

Check if any of the following defects is found in the pipe between the fuel pump and the exhaust fuel addition injector assembly.

·

Fuel leakage (loose joint bolt)

·

Clogging

·

Crush

·

Wrong assembly



Result:
Proceed to
OK
NG



OK

4.PERFORM PM FORCED REGENERATION

NG

7.REPAIR OR REPLACE DEFECTIVE PART
4.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.



Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Click hereEngine / Hybrid System>N04C-WA (ENGINE CONTROL)>ECD SYSTEM>DTC CHECK / CLEAR


e.

Read the DTCs.

Result:
Result Proceed to
DTC P20DE is output A
DTCs are not output B




A

6.REPLACE NO. 2 FUEL PRESSURE SENSOR

B

END

6.REPLACE NO. 2 FUEL PRESSURE SENSOR
a.

Replace the No. 2 fuel pressure sensor.

Click hereEngine / Hybrid System>N04C-WA (EMISSION CONTROL)>FUEL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.PERFORM PM FORCED REGENERATION
7.REPAIR OR REPLACE DEFECTIVE PART
a.

Repair or replace the defective part.


Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FUEL SYSTEM
8.BLEED AIR FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>N04C-WA (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

10.PERFORM PM FORCED REGENERATION
9.CONNECT SECURELY
a.

Connect securely the No. 2 fuel pressure sensor connector.

HINT:

Repair it as needed.



Result:
Proceed to
NEXT



NEXT

10.PERFORM PM FORCED REGENERATION
10.PERFORM PM FORCED REGENERATION
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / DPR Check.

i.

Select "Check Start" and check according to the GTS display.


ii.

Select "DPR ALL Items Reset" and reset according to the GTS display.


iii.

Exit the inspection screen.



d.

Clear the DTCs.

HINT:

Clear the DTCs with the engine stopped, as DTCs cannot be cleared while the engine is running.




Result:
Proceed to
NEXT



NEXT

11.CHECK DTC OUTPUT
11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END